Cryogenic process to separate high purity CO from mixture
I am looking for a cryogenic process to separate high purity CO (Carbon Monoxide) from a mixture of CO, CO2 and H2, plus small amounts of CH4.
ADVERTISEMENT
Cryo tempering business advice
My friend has a racing engine company in NC. He suggested I start a cryo tempering business there because of all the race shops around that source it out. Can you tell me or put me in touch with someone who can tell me what “turn key” would be required...
Open cycle coolers with capacity of 1,500 Q @ 100K?
Does anyone know of any open cycle coolers with a capacity of 1,500 Q @ 100K in the country, preferably as an off-the-shelf product?
Move cryogenic units in northern California?
Can you recommend any northern California companies that have expertise in moving cryogenic units?
Standards for fabrication of vessels/tanks?
I’m a total novice in the design and manufacture of cryogenic equipment, but nonetheless I’m a pressure vessel Designer/Engineer. Could you possibly advise as to any relevant standards/documentation that may be available with regard to, in particular, the fabrication of vessels/tanks?
Manufacturers of pressure regulators—liquid argon
I am trying to locate companies that manufacture and sell pressure regulators rated for dispensing liquid argon for a welding application. Do you know of companies that I could contact with this request?
ADVERTISEMENT
Stability
Stability refers to the ability of a device employing superconductors to remain in its superconducting state after part of the superconductor transitions back to its normal conducting state due to a disturbance. While the concept can apply to many superconducting devices—transmission lines, generators, motors, etc.—it is most commonly considered in...
Cable-in-Conduit Conductors
Cable-in-Conduit Conductors (CICC) are a common form of superconducting cable used in large-scale applications. There are several varieties of CICCs, but they all consist of many small, stabilized superconducting wires contained within a conduit through which a coolant (typically supercritical He II) flows. Figure 1 shows the cross section of...
Bayonet Coupling
A bayonet coupling is a demountable joint that allows for quick and easy connection and disconnection of cryogenic components, including transfer lines, cryostats, liquefiers and refrigerators. Bayonets provide a number of advantages, chief among them the ability to connect and disconnect the bayonets while components they connect are still at...
Primary Standards
Elie K. Track Hypres, Inc. elie@hypres.com http://www.hypres.com/ Primary standards involve the exact definition and realization of units of measurement for various quantities, time, length, mass, voltage, resistance, current, etc. International agreements based on the latest scientific knowledge define those units, and their realizations vary depending on the unit itself. For...
Shrink Fitting
Robin A. Rhodes Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Shrink fitting, (or “compression fitting” as it is sometimes called), is a method used to insert a pin or bushing into a housing or other assembly requiring an extremely tight tolerance fit. It can be used as an alternative to...
Telecommunications
From the Winter 2004 issue of Cold Facts magazine The recent M-Calc IV — 4th Industry Assessment workshop discussing military and commercial applications for low-cost cryocoolers, held in November in San Diego, highlighted progress being made in cryogenics as applied in telecommunications. The reliability and long lifetime of projects now...
Wind Tunnels
Dr. Robert Kilgore The development of the cryogenic wind tunnel is one of many significant breakthroughs in both cryogenics and wind-tunnel technology made during the past millennium. Interest in the development of high-speed commercial and military aircraft resulted in a review of problems of flow simulation in transonic wind tunnels...
An Issue of Pressure and Flow Rate in a Supply Tank
Please help solve this problem: A supply tank requires a vaporizer to generate sufficient pressure to pump stored fluid up into a vehicle or tank. The available head is limited as the tank level falls and it is important to minimize the system pressure drop to maintain the desired flow...
Using MLI on VJ Line Joints or Cryo Storage Tanks
When installing Multi Layer Insulation (MLI) blankets on VJ line joints or cryo storage tanks should they be wrapped and tied down tight or loose? These are usually pre-cut to size. Also should they have an access hole at the point of where the molecular sieve is installed to help...
Separated layers of ice over a pipe
I want to know that why there are different layers of ice over a pipe carrying a cryogenic fluid, each layer separated with clear marks / lines? What do these layers signify?