by Rob Early, Technical Manager, Compressed Gas Association
Growing interest in fuel cell electric vehicles (FCEVs) and other emerging applications is increasing the demand for hydrogen. Although many end uses consume hydrogen as a gas, the methods used to transport and store hydrogen evolve as customer demand grows.
For many hydrogen applications (particularly those involving new customers with relatively low consumption) hydrogen is supplied and transported in gaseous form. Gaseous hydrogen is delivered from the producer to the customer using tube trailers or high-pressure cylinders. The hydrogen may be stored in permanent ground storage (commonly called gas receivers) and tube trailers or cylinders may remain on-site to support operations.

However, as customers increase their hydrogen use, delivering and storing hydrogen solely in gaseous form becomes less practical. Meeting higher demand requires more deliveries and more frequent offloading activities. As the number of deliveries increases, so does the importance of strict adherence to established procedures to prevent incidents.
For these larger applications, liquid hydrogen often becomes the preferred supply option. Cryogenic liquid hydrogen storage systems use vaporizers to convert the liquid into gaseous hydrogen for the customer’s use.
A liquid hydrogen system can store significantly more hydrogen than a gaseous system. For perspective, a typical tube trailer or gas receiver may hold approximately 1,200 kilograms of hydrogen, while a large 18,000-gallon liquid hydrogen tank can store roughly 4,300 kilograms.
This increased storage capacity means fewer deliveries, less handling, and fewer interactions with the hydrogen system, reducing opportunities for operational errors and incidents.
The operational advantages of liquid hydrogen are significant, but the cryogenic nature of the product introduces unique hazards that require careful attention.
Cryogenic Hazards
In addition to hydrogen’s wide flammability range, liquid hydrogen presents hazards associated with its extremely low temperature. When exposed to the atmosphere, liquid hydrogen rapidly vaporizes and can create a cloud of flammable hydrogen gas. Preventing spills and minimizing releases are therefore essential.
Liquid hydrogen is also cold enough to condense and liquefy atmospheric gases such as oxygen and, under some conditions, freeze certain constituents of air. Because helium remains gaseous at liquid hydrogen temperatures, it is often the only common gas that will not condense or freeze under these conditions.
For this reason, air and moisture should be removed from hydrogen equipment and piping before a system is placed into service.
Pressure Management Considerations
Liquid hydrogen can freeze water. As a result, water should not be sprayed directly onto the vent stack of a liquid hydrogen storage tank during firefighting operations.
Cold hydrogen gas can freeze the water spray, blocking the vent stack and preventing pressure relief devices from functioning as intended. If pressure cannot be relieved, overpressure conditions could develop and potentially result in tank rupture.
Maintaining clear relief paths is critical to the safe operation of liquid hydrogen systems.
Air Condensation and Oxygen Enrichment
Many cryogenic fluids (such as liquid nitrogen) can flow through bare piping, resulting in frost formation on the outside of the pipe. Liquid hydrogen behaves differently.

Because of its lower temperature, liquid hydrogen can cause atmospheric gases to liquefy on the exterior surface of uninsulated piping. The resulting liquid may resemble a water leak, but it is actually condensed air.
As this liquid air evaporates, it can leave behind oxygen-enriched areas. In the presence of greases, oils, or other hydrocarbon materials, these oxygen-rich conditions can increase the likelihood of enhanced combustion from a spark or static discharge.
This hazard can be mitigated by using vacuum insulated piping to prevent liquid air formation. Where vacuum insulation is not practical, aluminum or stainless steel drip trays may be installed beneath the piping to capture the condensed air and allow all constituents to evaporate safely.
Safe Transfer Practices
Liquid hydrogen transfers should occur over clean concrete surfaces free from oil and grease.
Transfers conducted over gravel present additional concerns because oils or hydrocarbons may have migrated below the surface and remain out of sight. Condensed liquid air can drip into the gravel and come into contact with these materials, creating conditions that support ignition.
Proper housekeeping and transfer area design are important components of safe liquid hydrogen operations.
A Long History of Safe Use
The unique properties of liquid hydrogen require thoughtful system design, operator training, and adherence to established procedures. These considerations are not barriers to its use. Rather, they are the reason liquid hydrogen has been transported, delivered, and used safely for decades across industrial, aerospace, and emerging energy applications.
Understanding the hazards and implementing proven safeguards allow organizations to realize the benefits of liquid hydrogen while maintaining safe and reliable operations.
For additional guidance on handling liquid hydrogen, consult CGA G-5, Hydrogen, https://portal.cganet.com/publication/G-5/details, and CGA P-12, Safe Handling of Cryogenic Fluids, https://portal.cganet.com/publication/P-12/details.
About the Compressed Gas Association
The Compressed Gas Association (CGA) is the leading authority on safety standards for industrial, medical, food, and specialty gases and equipment. Since 1913, CGA has developed nearly 500 globally recognized standards, trusted by ISO, NFPA, the United Nations, and regulatory bodies worldwide. Representing members who support over 34,000 US jobs and contribute more than $30 billion to the American economy, CGA advances safety, drives innovation, and fosters professional development across the compressed gas industry.
Rob Early is a technical manager at the Compressed Gas Association with more than 20 years of experience in hydrogen and compressed gas systems. Before joining CGA in 2018, he worked for Praxair, now Linde, developing gas supply systems and industry standards. He currently chairs the US Technical Advisory Group for ISO/TC 197/SC 1.








