ADVERTISEMENT

Paragraf Takes Graphene to Cryogenic Temperatures

Graphene has long been pursued as a medium for electronics in the world of academia. However, until recently, it has struggled to make its way into the industry. Paragraf, a UK-based company, is the first and only company to achieve this feat to date. Two months ago, All About Circuits...

Catalent Adds Cryogenic Capabilities at Philadelphia Clinical Supply Services Facility

On April 15, Catalent, a leading global provider of advanced delivery technologies, development, manufacturing and clinical supply solutions for drugs, biologics, cell and gene therapies, and consumer health products, announced that it has made an investment to expand cryogenic capabilities at its clinical supply services facility in Philadelphia to support...

Argonaut Project Launches Design Effort for Supercold Robotics

A new robotics project announced at the Department of Energy’s Fermi National Accelerator Laboratory (CSA CSM) on May 20, Argonaut’s mission will be to monitor conditions within ultracold particle detectors by voyaging into a sea of liquid argon kept at -193 degrees Celsius—as cold as some of the moons of...

Cryogenic Electronics: Part 2

This is Part 2 of a two-part article about cryogenic semiconductor electronics. Part 1 appeared in the preceding Cold Facts (Vol 37, No 1); it gave a brief introduction and presented applications of cryogenic electronics for sensors and spacecraft, microwave receivers, and power conversion. This part presents additional application examples,...

ADVERTISEMENT

Helium-3

Helium-3 (3He) is one of the two stable isotopes of helium. The other is the much more common Helium-4 (4He). Neither of these isotopes should be confused with He II, which is the second liquid phase of 4He. He II was discussed in this column in the Spring 2010 edition...

Cryopumping

Cryopumping refers to the use of cryogenic temperatures to produce vacuum in enclosed spaces. More broadly, it can also refer to the removal of gases via cryogenic temperatures from a flow stream or enclosure without necessarily resulting in vacuum pressures. This is an important application of cryogenics and is used...

Thermal Acoustic Oscillations

Thermal Acoustic Oscillations (TAO) are a common event in cryogenic systems that can have significant adverse effects on the performance of the system. TAOs are sustained pressure oscillations that can occur in tubes containing gas, closed at one end (the warm end) that have a very large temperature gradient along...

Primary Standards

Elie K. Track Hypres, Inc. elie@hypres.com http://www.hypres.com/ Primary standards involve the exact definition and realization of units of measurement for various quantities, time, length, mass, voltage, resistance, current, etc. International agreements based on the latest scientific knowledge define those units, and their realizations vary depending on the unit itself. For...

Shrink Fitting

Robin A. Rhodes Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Shrink fitting, (or “compression fitting” as it is sometimes called), is a method used to insert a pin or bushing into a housing or other assembly requiring an extremely tight tolerance fit. It can be used as an alternative to...

Telecommunications

From the Winter 2004 issue of Cold Facts magazine The recent M-Calc IV — 4th Industry Assessment workshop discussing military and commercial applications for low-cost cryocoolers, held in November in San Diego, highlighted progress being made in cryogenics as applied in telecommunications. The reliability and long lifetime of projects now...

Wind Tunnels

Dr. Robert Kilgore The development of the cryogenic wind tunnel is one of many significant breakthroughs in both cryogenics and wind-tunnel technology made during the past millennium. Interest in the development of high-speed commercial and military aircraft resulted in a review of problems of flow simulation in transonic wind tunnels...

An Issue of Pressure and Flow Rate in a Supply Tank

Please help solve this problem: A supply tank requires a vaporizer to generate sufficient pressure to pump stored fluid up into a vehicle or tank. The available head is limited as the tank level falls and it is important to minimize the system pressure drop to maintain the desired flow...

Using MLI on VJ Line Joints or Cryo Storage Tanks

When installing Multi Layer Insulation (MLI) blankets on VJ line joints or cryo storage tanks should they be wrapped and tied down tight or loose? These are usually pre-cut to size. Also should they have an access hole at the point of where the molecular sieve is installed to help...