ADVERTISEMENT

Argonaut Project Launches Design Effort for Supercold Robotics

A new robotics project announced at the Department of Energy’s Fermi National Accelerator Laboratory (CSA CSM) on May 20, Argonaut’s mission will be to monitor conditions within ultracold particle detectors by voyaging into a sea of liquid argon kept at -193 degrees Celsius—as cold as some of the moons of...

Cryogenic Electronics: Part 2

This is Part 2 of a two-part article about cryogenic semiconductor electronics. Part 1 appeared in the preceding Cold Facts (Vol 37, No 1); it gave a brief introduction and presented applications of cryogenic electronics for sensors and spacecraft, microwave receivers, and power conversion. This part presents additional application examples,...

Women in Cryogenics and Superconductivity 2021

CSA celebrates women in cryogenics and superconductivity. In this feature, seven women in positions across the industry discuss current projects, how they entered the field and their thoughts on attracting more women to the profession.

Who is Frosty?

You have seen the cute little white smiling CSA mascot, “Frosty,” with our logo on his tummy. You may have wondered about his story. We’ve been featuring Frosty in many iterations, especially in the CryoChronicle, with holiday themes and—more recently—with a mask reminding us to be safe during this pandemic....

ADVERTISEMENT

Joule-Thomson Effect

The Joule-Thomson (JT) effect is a thermodynamic process that occurs when a fluid expands from high pressure to low pressure at constant enthalpy (an isenthalpic process). Such a process can be approximated in the real world by expanding a fluid from high pressure to low pressure across a valve. Under...

Current Leads

One of the challenges of using superconducting magnets is the connection of the magnet to a room temperature power supply. This is accomplished via current leads. The trick is that current leads should ideally have a low heat leak, since they connect room temperature to cryogenic temperature, while at the...

Multilayer Insulation

Multilayer insulation (also referred to as superinsulation) is a key component in the reduction of heat leak to cryogenic systems due to thermal radiation. MLI consists of a series of uncooled reflective surfaces placed in the vacuum space between two surfaces, one warmer than the other. Generally speaking, for ideal...

Primary Standards

Elie K. Track Hypres, Inc. elie@hypres.com http://www.hypres.com/ Primary standards involve the exact definition and realization of units of measurement for various quantities, time, length, mass, voltage, resistance, current, etc. International agreements based on the latest scientific knowledge define those units, and their realizations vary depending on the unit itself. For...

Shrink Fitting

Robin A. Rhodes Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Shrink fitting, (or “compression fitting” as it is sometimes called), is a method used to insert a pin or bushing into a housing or other assembly requiring an extremely tight tolerance fit. It can be used as an alternative to...

Telecommunications

From the Winter 2004 issue of Cold Facts magazine The recent M-Calc IV — 4th Industry Assessment workshop discussing military and commercial applications for low-cost cryocoolers, held in November in San Diego, highlighted progress being made in cryogenics as applied in telecommunications. The reliability and long lifetime of projects now...

Wind Tunnels

Dr. Robert Kilgore The development of the cryogenic wind tunnel is one of many significant breakthroughs in both cryogenics and wind-tunnel technology made during the past millennium. Interest in the development of high-speed commercial and military aircraft resulted in a review of problems of flow simulation in transonic wind tunnels...

An Issue of Pressure and Flow Rate in a Supply Tank

Please help solve this problem: A supply tank requires a vaporizer to generate sufficient pressure to pump stored fluid up into a vehicle or tank. The available head is limited as the tank level falls and it is important to minimize the system pressure drop to maintain the desired flow...

Using MLI on VJ Line Joints or Cryo Storage Tanks

When installing Multi Layer Insulation (MLI) blankets on VJ line joints or cryo storage tanks should they be wrapped and tied down tight or loose? These are usually pre-cut to size. Also should they have an access hole at the point of where the molecular sieve is installed to help...