Success after a Three-year Sprint
ProtoDUNE scientists rushed to develop the project’s first large prototype detector, resulting in an amazing display of the technology being created for the Deep Underground Neutrino Experiment.
ADVERTISEMENT
UCSD Students Prepared to Launch Vulcan II
A team of engineering students from UC San Diego has developed a test rocket that features a 3D printed engine that incorporates liquid oxygen and kerosene RP-1. The updated rocket is called Vulcan II, and represents a vessel the students will attempt to launch roughly six miles into the atmosphere...
Fermilab Using ArgoNeuT Data to Advance Future Measurement of Neutrinos in Liquid Argon
Scientists at Fermi National Accelerator Laboratory (CSA CSM) have continued to analyze data from the retired ArgoNeuT neutrino detector, developing processes to improve future simulations and software that finds particles in liquid-argon based neutrino detectors.
Cryoforce Spectroscopy Reveals DNA Mechanical Properties
Physicists from the University of Basel have developed a low temperature method to examine the elasticity and binding properties of DNA molecules. The process utilized cryoforce spectroscopy and computer simulations, a combination that revealed DNA molecules behaving like a chain of small coil springs.
CAL Performing Coolest Experiments in the Universe
NASA's Cold Atom Lab (CAL) is the first facility inside the International Space Station to produce clouds of "ultracold" atoms that can reach a fraction of a degree above absolute zero.
New Theory Sends Kelvin Temperature Below Current Low
A recent collaboration of researchers has shown that it is possible, in principle, to measure temperatures below a billionth of a kelvin without significantly disturbing the Bose-Einstein condensate used in the study.
ADVERTISEMENT
Cold Compressors
A common way to provide cooling below the normal boiling point of helium (4.2K) is to reduce the pressure above the bath of liquid helium, thus also reducing the bath’s equilibrium saturation temperature. For example, to produce a 1.8K bath of liquid helium, the saturation pressure has to be reduced...
Kapitza Conductance
Kapitza conductance refers to the heat transfer between a solid surface and a fluid that covers that surface. Fundamentally, it describes the inherent difficulty in transferring energy from a solid to the fluid covering the solid surface. This phenomenon was first observed by P. L. Kapitza in 1941 while studying...
Thermosyphons
A thermosyphon (or thermosiphon) is a device that transfers heat via natural convection in a fluid. The natural convection is driven by gravity with the colder, denser fluid flowing downhill and the warmer, less dense fluid flowing back up. Thus, thermosyphons connect an object to be cooled with a reservoir...
Air Separation and Liquefaction
by Nils Tellier, PE, President, EPSIM Corporation (CSA CSM) nils@epsim.us All illustrations courtesy EPSIM Corporation Background History of Air Separation and Liquefaction This section builds on a rich history of methods to develop deep refrigeration and cryogenic liquefaction during the 19th Century. You are encouraged to read Cryo Central’s History...
Bose-Einstein Condensate
A Bose-Einstein condensate, first proposed in 1925 by Albert Einstein based on work done by Satyendra Nath Bose (the same Bose from whom the term boson is derived), is a super-cold state of matter in which almost all of the individual atoms have “condensed” down to the lowest possible quantum...
Cold Technology for Pest Control
While it does not reach temperatures cold enough to be called cryogenic, carbon dioxide snow is at the heart of a new way of dealing with unwanted pests. It utilizes a quick freezing process that takes advantage of the properties of carbon dioxide snow and has a number of benefits...
Cryogenic Finishing
The following 3 articles discuss the uses and procedures of various type of cryogenic finishing. 1) By Robin A. Rhodes, Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Cryogenic Deflashing is employed to remove undesired residual mold flash that remains on molded parts after they are removed or ejected from the...
Manufacturer for a machine to liquefy natural gas or methane gas.
I’m in search of a company to manufacture a machine to liquefy natural gas or methane gas.
Need a plastic for diffuser on the magnet end of a LHe fill siphon
I am trying to select a plastic to be used as a diffuser on the magnet end of a LHe fill siphon. Can you recommend anything that will hold up at LHe temps? I have seen some and they look like HDPE or Polypropylene but I am not sure.
Thermal conductivity orthotropic properties from 300K up to 500K
I am looking for the thermal conductivity orthotropic properties from 300K up to 500K (or even higher, if available). “Cryocomp” provides orthotropic data on G-10 (Fill, Warp, Normal) only up to 300K.
Looking for heat conductivity values of CuCrZr in the low temperature range of 4 to 300K
I’m a student of physical engineering and I am looking for heat conductivity values of CuCrZr in the low temperature range of 4 to 300K. Jakub Voňka Brno University of Technology Faculty of Mechanical Engineering