ADVERTISEMENT

Toward a Standardized ODH Analysis Technique

Standardization of ODH analysis and mitigation policy thus represents an opportunity for the cryogenic community. There are several benefits for industry and government facilities to develop an applicable unified standard for ODH. The number of reviewers would increase, and review projects across different facilities would be simpler. It would also...

Whole Body Cryotherapy

Interest in low temperature treatment is increasing and whole body cryotherapy (WBC) devices are becoming available not only in medical centers but also in local gyms and spa centers. Many governments and medical professionals have thus turned attention to WBC, evaluating the treatment for its effectiveness and safety. The US...

Cryocoolers 19 Proceedings Available Now

"Cryocoolers 19," a 654-page compilation of the proceedings of the 19th International Cryocooler Conference held in San Diego, California, June 20-23, 2016, is now available and has been mailed to registered participants. Published by ICC Press, Boulder, Colorado, and edited by S.D. Miller and R.G. Ross, Jr., the volume features...

CERN Ramps Up Neutrino Program

In the midst of the verdant French countryside looms a workshop the size of an aircraft hangar. Inside, CERN technicians are busy constructing two 8-meter tall cubes to test prototype detectors for the Deep Underground Neutrino Experiment (DUNE). Each will in time contain 770 metric tons of liquid argon permeated...

NIST Physicists Squeeze Light, Cool Microscopic Drum below Quantum Limit

Physicists at the National Institute of Standards and Technology (NIST) have cooled a microscopic mechanical drum to less than one-fifth of a single quantum, or packet of energy. The result, according to the research team, is lower than ordinarily predicted by quantum physics and the technique used could theoretically cool...

ADVERTISEMENT

Mixed Refrigerant Cycles

Most cryogenic refrigeration systems, both large scale systems and cryocoolers, use helium as a working fluid. There are a number of advantages to helium, not the least of which is that helium remains a fluid down to the lowest achievable temperatures. In order to freeze helium, pressures of over 20...

Fountain Pumps and He II Phase Separators

Helium II (He II), the second liquid phase of the 4He isotope described in this column in Cold Facts Spring 2010 (http://2csa.us/he2), can be modeled as consisting of two interpenetrating fluids. One, the superfluid component, has zero viscosity and entropy and the other, the normal fluid component, has nonzero viscosity...

Turboexpanders

A vital technology in the refrigerators and liquefiers described in Cold Facts Volume 31 Number 3 is that of turboexpanders. These devices are rotating machines in which the process fluid (e.g., helium) does work against the turboexpander while moving from high pressure to a lower pressure and thus is cooled....

Air Separation and Liquefaction

by Nils Tellier, PE, President, EPSIM Corporation (CSA CSM) nils@epsim.us All illustrations courtesy EPSIM Corporation Background History of Air Separation and Liquefaction This section builds on a rich history of methods to develop deep refrigeration and cryogenic liquefaction during the 19th Century. You are encouraged to read Cryo Central’s History...

Bose-Einstein Condensate

A Bose-Einstein condensate, first proposed in 1925 by Albert Einstein based on work done by Satyendra Nath Bose (the same Bose from whom the term boson is derived), is a super-cold state of matter in which almost all of the individual atoms have “condensed” down to the lowest possible quantum...

Cold Technology for Pest Control

While it does not reach temperatures cold enough to be called cryogenic, carbon dioxide snow is at the heart of a new way of dealing with unwanted pests. It utilizes a quick freezing process that takes advantage of the properties of carbon dioxide snow and has a number of benefits...

Cryogenic Finishing

The following 3 articles discuss the uses and procedures of various type of cryogenic finishing. 1) By Robin A. Rhodes, Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Cryogenic Deflashing is employed to remove undesired residual mold flash that remains on molded parts after they are removed or ejected from the...

Presence of alloying elements in tool steels

I want to expand my knowledge of cryogenics in general and tool steels in particular. Specifically, I am keenly interested in learning about the presence of alloying elements in tool steels and how their presence in various combinations affects the performance of tool steels after cryogenic treatment.

Pros and cons of barcoding samples

I was wondering if I could ask for input on pros and cons of barcoding. We are in the process of trying to decide if we should start barcoding our samples and I’m just not sure if this is feasible for our organization. We have numerous sites all over the...