With the delivery of two feedthrough samples for the 6 pin 30 KV rating, identified as a type D variant, Ceramtec North America Corporation (US) has begun to solve one of the big challenges at ITER.
Since shutting down in early 2013, the LHC and its detectors have undergone a multitude of upgrades and repairs. When the particle accelerator restarts, it will collide protons at an unprecedented energy: 13 trillion electron volts. The upgraded capabilities of the ATLAS, CMS, ALICE and LHCb detectors—plus the LHC’s extra...
Many industries are calling for electronics that can operate reliably in a harsh environment, including extreme temperatures above 200°C. A team of researchers from the University of California, Riverside and Rensselaer Polytechnic Institute discovered that molybdenum disulfide, a semiconductor material, may be a promising candidate to make thin-film transistors for...
In 2015, Fermilab will intensify its contribution to the Linac Coherent Light Source II (LCLS-II), an electron accelerator project at SLAC National Accelerator Laboratory, in the overlapping areas of superconducting radio-frequency accelerator technology and cryogenics.
Elevators are about to get a major upgrade: the ability to go sideways, thanks to magnetic levitation technology. German industrial behemoth ThyssenKrupp is promising that two-axis travel ("the holy grail of the elevator industry") will revolutionize intra-building travel, and that they will have it operational in 2016.
A new study by a team of physicists adds to the growing body of evidence supporting a theory that strange electronic behaviors, including high temperature superconductivity and heavy fermion physics, arise from quantum fluctuations of strongly correlated electrons. The study describes results from a series of experiments that tested for...
A common way to provide cooling below the normal boiling point of helium (4.2K) is to reduce the pressure above the bath of liquid helium, thus also reducing the bath’s equilibrium saturation temperature. For example, to produce a 1.8K bath of liquid helium, the saturation pressure has to be reduced...
Kapitza conductance refers to the heat transfer between a solid surface and a fluid that covers that surface. Fundamentally, it describes the inherent difficulty in transferring energy from a solid to the fluid covering the solid surface. This phenomenon was first observed by P. L. Kapitza in 1941 while studying...
A thermosyphon (or thermosiphon) is a device that transfers heat via natural convection in a fluid. The natural convection is driven by gravity with the colder, denser fluid flowing downhill and the warmer, less dense fluid flowing back up. Thus, thermosyphons connect an object to be cooled with a reservoir...
by Nils Tellier, PE, President, EPSIM Corporation (CSA CSM) nils@epsim.us All illustrations courtesy EPSIM Corporation Background History of Air Separation and Liquefaction This section builds on a rich history of methods to develop deep refrigeration and cryogenic liquefaction during the 19th Century. You are encouraged to read Cryo Central’s History...
A Bose-Einstein condensate, first proposed in 1925 by Albert Einstein based on work done by Satyendra Nath Bose (the same Bose from whom the term boson is derived), is a super-cold state of matter in which almost all of the individual atoms have “condensed” down to the lowest possible quantum...
While it does not reach temperatures cold enough to be called cryogenic, carbon dioxide snow is at the heart of a new way of dealing with unwanted pests. It utilizes a quick freezing process that takes advantage of the properties of carbon dioxide snow and has a number of benefits...
The following 3 articles discuss the uses and procedures of various type of cryogenic finishing. 1) By Robin A. Rhodes, Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Cryogenic Deflashing is employed to remove undesired residual mold flash that remains on molded parts after they are removed or ejected from the...
We are looking for manufacturers of cryogenic dewars with infrared detectors (long wave). We need these dewars for repairing infrared systems (thermographic systems) and we cannot find such glass dewars. Do you know any manufacturers’ addresses?
Would you please suggest a few manufacturers that produce cryogenic regenerator lead spheres? The size we need is 0.15mm-0.2mm. I don’t have a lot of ideas for where to go to purchase them.
We are fabricating piping components for refrigeration service. These components must be leak checked at 15 bar (218 psig). We are using a gas test media that is 25% helium and experiencing difficulty on maintaining a seal on the flanged connections. Do you know anyone or any references that could...
Could anyone please help me out with the following cryogenics data: Leather — mechanical properties at 77 K or lower Nomex — thermal conductivity @ 4 to 50 K I lost the data I had some time ago and although this should be easily accessible, I can’t find any reference...