With the delivery of two feedthrough samples for the 6 pin 30 KV rating, identified as a type D variant, Ceramtec North America Corporation (US) has begun to solve one of the big challenges at ITER.
Since shutting down in early 2013, the LHC and its detectors have undergone a multitude of upgrades and repairs. When the particle accelerator restarts, it will collide protons at an unprecedented energy: 13 trillion electron volts. The upgraded capabilities of the ATLAS, CMS, ALICE and LHCb detectors—plus the LHC’s extra...
Many industries are calling for electronics that can operate reliably in a harsh environment, including extreme temperatures above 200°C. A team of researchers from the University of California, Riverside and Rensselaer Polytechnic Institute discovered that molybdenum disulfide, a semiconductor material, may be a promising candidate to make thin-film transistors for...
In 2015, Fermilab will intensify its contribution to the Linac Coherent Light Source II (LCLS-II), an electron accelerator project at SLAC National Accelerator Laboratory, in the overlapping areas of superconducting radio-frequency accelerator technology and cryogenics.
Elevators are about to get a major upgrade: the ability to go sideways, thanks to magnetic levitation technology. German industrial behemoth ThyssenKrupp is promising that two-axis travel ("the holy grail of the elevator industry") will revolutionize intra-building travel, and that they will have it operational in 2016.
A new study by a team of physicists adds to the growing body of evidence supporting a theory that strange electronic behaviors, including high temperature superconductivity and heavy fermion physics, arise from quantum fluctuations of strongly correlated electrons. The study describes results from a series of experiments that tested for...
The Joule-Thomson (JT) effect is a thermodynamic process that occurs when a fluid expands from high pressure to low pressure at constant enthalpy (an isenthalpic process). Such a process can be approximated in the real world by expanding a fluid from high pressure to low pressure across a valve. Under...
One of the challenges of using superconducting magnets is the connection of the magnet to a room temperature power supply. This is accomplished via current leads. The trick is that current leads should ideally have a low heat leak, since they connect room temperature to cryogenic temperature, while at the...
Multilayer insulation (also referred to as superinsulation) is a key component in the reduction of heat leak to cryogenic systems due to thermal radiation. MLI consists of a series of uncooled reflective surfaces placed in the vacuum space between two surfaces, one warmer than the other. Generally speaking, for ideal...
by Nils Tellier, PE, President, EPSIM Corporation (CSA CSM) nils@epsim.us All illustrations courtesy EPSIM Corporation Background History of Air Separation and Liquefaction This section builds on a rich history of methods to develop deep refrigeration and cryogenic liquefaction during the 19th Century. You are encouraged to read Cryo Central’s History...
A Bose-Einstein condensate, first proposed in 1925 by Albert Einstein based on work done by Satyendra Nath Bose (the same Bose from whom the term boson is derived), is a super-cold state of matter in which almost all of the individual atoms have “condensed” down to the lowest possible quantum...
While it does not reach temperatures cold enough to be called cryogenic, carbon dioxide snow is at the heart of a new way of dealing with unwanted pests. It utilizes a quick freezing process that takes advantage of the properties of carbon dioxide snow and has a number of benefits...
The following 3 articles discuss the uses and procedures of various type of cryogenic finishing. 1) By Robin A. Rhodes, Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Cryogenic Deflashing is employed to remove undesired residual mold flash that remains on molded parts after they are removed or ejected from the...
Could you please tell me what is the temperature range of cryogenics? In other words, is -100°F considered cryogenic, or does it start lower? Could I expect to see some extended life in D2 stamping dies? What would the recipe be to achieve the desired results using cryogenics?