Ready to launch the prototype: HTS current leads for ITER
High Temperature Superconductor (HTS) current leads are the components that transmit the large currents from room-temperature power supplies to very low-temperature superconducting coils.
ADVERTISEMENT
High-tech storage holds the key to preserving plant life
About half the world's plant species are estimated to be under threat of extinction, and Australia is home to 14 percent of them. It is now hoped a cryogenic storage unit can protect Australia's native plants forever.
Bestobell supplies valves for first US LNG flag vessel
The first US flag vessel to be operated on liquefied natural gas uses valves supplied by Bestobell Valves (CSA CSM). Globe and check valves were supplied as part of the LNGPac fuel system through the company’s preferred supplier agreement with Wärtsilä Gas Power Systems (GPS).
Scientists create first computer-designed superconductor
A Binghamton University scientist and his international colleagues report on the successful synthesis of the first superconductor designed entirely on the computer. Their findings were published in Physical Review Letters.
Higgs, Englert Win Nobel for Particle Mass Discoveries
On October 8 François Englert of Belgium and Peter Higgs of Britain were awarded the 2013 Nobel Prize in physics for their theoretical discoveries on how subatomic particles acquire mass.
VIDEO: A guided tour around the CLIC test facility
The Compact Linear Collider (CLIC) is a study for a future accelerator that will reach unprecedented energies for electrons and their antimatter twins, positrons.
ADVERTISEMENT
Cold Compressors
A common way to provide cooling below the normal boiling point of helium (4.2K) is to reduce the pressure above the bath of liquid helium, thus also reducing the bath’s equilibrium saturation temperature. For example, to produce a 1.8K bath of liquid helium, the saturation pressure has to be reduced...
Kapitza Conductance
Kapitza conductance refers to the heat transfer between a solid surface and a fluid that covers that surface. Fundamentally, it describes the inherent difficulty in transferring energy from a solid to the fluid covering the solid surface. This phenomenon was first observed by P. L. Kapitza in 1941 while studying...
Thermosyphons
A thermosyphon (or thermosiphon) is a device that transfers heat via natural convection in a fluid. The natural convection is driven by gravity with the colder, denser fluid flowing downhill and the warmer, less dense fluid flowing back up. Thus, thermosyphons connect an object to be cooled with a reservoir...
Air Separation and Liquefaction
by Nils Tellier, PE, President, EPSIM Corporation (CSA CSM) nils@epsim.us All illustrations courtesy EPSIM Corporation Background History of Air Separation and Liquefaction This section builds on a rich history of methods to develop deep refrigeration and cryogenic liquefaction during the 19th Century. You are encouraged to read Cryo Central’s History...
Bose-Einstein Condensate
A Bose-Einstein condensate, first proposed in 1925 by Albert Einstein based on work done by Satyendra Nath Bose (the same Bose from whom the term boson is derived), is a super-cold state of matter in which almost all of the individual atoms have “condensed” down to the lowest possible quantum...
Cold Technology for Pest Control
While it does not reach temperatures cold enough to be called cryogenic, carbon dioxide snow is at the heart of a new way of dealing with unwanted pests. It utilizes a quick freezing process that takes advantage of the properties of carbon dioxide snow and has a number of benefits...
Cryogenic Finishing
The following 3 articles discuss the uses and procedures of various type of cryogenic finishing. 1) By Robin A. Rhodes, Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Cryogenic Deflashing is employed to remove undesired residual mold flash that remains on molded parts after they are removed or ejected from the...
An Issue of Pressure and Flow Rate in a Supply Tank
Please help solve this problem: A supply tank requires a vaporizer to generate sufficient pressure to pump stored fluid up into a vehicle or tank. The available head is limited as the tank level falls and it is important to minimize the system pressure drop to maintain the desired flow...
Using MLI on VJ Line Joints or Cryo Storage Tanks
When installing Multi Layer Insulation (MLI) blankets on VJ line joints or cryo storage tanks should they be wrapped and tied down tight or loose? These are usually pre-cut to size. Also should they have an access hole at the point of where the molecular sieve is installed to help...
Separated layers of ice over a pipe
I want to know that why there are different layers of ice over a pipe carrying a cryogenic fluid, each layer separated with clear marks / lines? What do these layers signify?