MicroBooNE begins construction, elects co-spokesperson
Fermilab's neutrino experiment, MicroBooNE, is beginning the full construction phase for the detector, after DOE announced the official Critical Decision 3b approval on March 29.
ADVERTISEMENT
CLNG president responds to senator’s comments on LNG exports
In response to comments from U.S. Sen. Ron Wyden suggesting the United States needs a policy on energy exports and that a "timeout" should be declared on permits to export LNG to non-Free Trade Agreement countries, Center for Liquefied Natural Gas (CLNG) President Bill Cooper issued the following statement:
Linde introduces new N2 pressure booster
Gas-assist injection molders (GAIM) can improve efficiency and quality -- even on lightweight parts and difficult geometries -- with the help of a new liquid nitrogen (N2) pressure booster from Linde North America.
Argonne named a “Best Place” for postdocs to work
For postdoctoral scholars, or postdocs, Argonne National Laboratory is the 6th best place to work in the United States, according to The Scientist, a life sciences magazine.
At DOE, body blows to fusion, nuclear physics and particle physics
Overall, the 2013 budget numbers for the Department of Energy's (DOE's) Office of Science, the single largest funder of physical sciences research in the United States, look reasonably good. The office would see its budget climb by 2.4% to $4.992 billion. Three of the office's six major research programs, however,...
CERN experiment makes spectroscopic measurement of antihydrogen
In a paper published online on March 7 by the journal Nature, the ALPHA collaboration at CERN reports an important milestone on the way to measuring the properties of antimatter atoms.
ADVERTISEMENT
Refrigerators and Liquefiers
Two of the most common terms used in cryogenics are “refrigerator” and “liquefier.” These terms describe similar and, as will be seen, in some cases identical components. A refrigerator provides cooling (that is, absorbs heat) at cryogenic temperatures. Refrigerators typically put a working fluid (such as helium) through one of...
Air Separation
Air separation is one of the largest, as well as earliest, industrial applications of cryogenics. In this process, cryogenic temperatures are used to separate air into its constituent gases: nitrogen (78.08%), oxygen (20.95%), argon (0.93%) and carbon dioxide (0.3%). Trace gases such as krypton, neon, xenon and helium total far...
Coefficient of Performance and Figure of Merit
The coefficient of performance (COP) is used to describe the effectiveness of refrigerators, including those operating at cryogenic temperatures. The COP is defined as the amount of heat removed at the cryogenic operating temperature of the refrigerator divided by the amount of work that must be applied to remove the...
Air Separation and Liquefaction
by Nils Tellier, PE, President, EPSIM Corporation (CSA CSM) nils@epsim.us All illustrations courtesy EPSIM Corporation Background History of Air Separation and Liquefaction This section builds on a rich history of methods to develop deep refrigeration and cryogenic liquefaction during the 19th Century. You are encouraged to read Cryo Central’s History...
Bose-Einstein Condensate
A Bose-Einstein condensate, first proposed in 1925 by Albert Einstein based on work done by Satyendra Nath Bose (the same Bose from whom the term boson is derived), is a super-cold state of matter in which almost all of the individual atoms have “condensed” down to the lowest possible quantum...
Cold Technology for Pest Control
While it does not reach temperatures cold enough to be called cryogenic, carbon dioxide snow is at the heart of a new way of dealing with unwanted pests. It utilizes a quick freezing process that takes advantage of the properties of carbon dioxide snow and has a number of benefits...
Cryogenic Finishing
The following 3 articles discuss the uses and procedures of various type of cryogenic finishing. 1) By Robin A. Rhodes, Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Cryogenic Deflashing is employed to remove undesired residual mold flash that remains on molded parts after they are removed or ejected from the...
In need of books to start a cryogenic engineering department
My company is going to create a cryogenic engineering department and we need some books in order to facilitate this project. This is the kind of information we would like to obtain from the books: 1- Calculations for determining the storage facilities, such as storage tanks, pumps, compressors, etc. 2-...
Having some difficulty with the design of a cryogenic pressure vessel
I am a graduate student in the Dept. of Mechanical Engineering at West Virginia University. As a part of my research, I’m doing a case study of design of a Cryogenic Pressure Vessel. I’m facing a little difficulty in the process, and would be very grateful to you if you...
What's the difference between a cryocooler and a cryostat?
What’s the difference between a cryocooler and a cryostat?