MicroBooNE begins construction, elects co-spokesperson
Fermilab's neutrino experiment, MicroBooNE, is beginning the full construction phase for the detector, after DOE announced the official Critical Decision 3b approval on March 29.
ADVERTISEMENT
CLNG president responds to senator’s comments on LNG exports
In response to comments from U.S. Sen. Ron Wyden suggesting the United States needs a policy on energy exports and that a "timeout" should be declared on permits to export LNG to non-Free Trade Agreement countries, Center for Liquefied Natural Gas (CLNG) President Bill Cooper issued the following statement:
Linde introduces new N2 pressure booster
Gas-assist injection molders (GAIM) can improve efficiency and quality -- even on lightweight parts and difficult geometries -- with the help of a new liquid nitrogen (N2) pressure booster from Linde North America.
Argonne named a “Best Place” for postdocs to work
For postdoctoral scholars, or postdocs, Argonne National Laboratory is the 6th best place to work in the United States, according to The Scientist, a life sciences magazine.
At DOE, body blows to fusion, nuclear physics and particle physics
Overall, the 2013 budget numbers for the Department of Energy's (DOE's) Office of Science, the single largest funder of physical sciences research in the United States, look reasonably good. The office would see its budget climb by 2.4% to $4.992 billion. Three of the office's six major research programs, however,...
CERN experiment makes spectroscopic measurement of antihydrogen
In a paper published online on March 7 by the journal Nature, the ALPHA collaboration at CERN reports an important milestone on the way to measuring the properties of antimatter atoms.
ADVERTISEMENT
Helium-3
Helium-3 (3He) is one of the two stable isotopes of helium. The other is the much more common Helium-4 (4He). Neither of these isotopes should be confused with He II, which is the second liquid phase of 4He. He II was discussed in this column in the Spring 2010 edition...
Cryopumping
Cryopumping refers to the use of cryogenic temperatures to produce vacuum in enclosed spaces. More broadly, it can also refer to the removal of gases via cryogenic temperatures from a flow stream or enclosure without necessarily resulting in vacuum pressures. This is an important application of cryogenics and is used...
Thermal Acoustic Oscillations
Thermal Acoustic Oscillations (TAO) are a common event in cryogenic systems that can have significant adverse effects on the performance of the system. TAOs are sustained pressure oscillations that can occur in tubes containing gas, closed at one end (the warm end) that have a very large temperature gradient along...
Air Separation and Liquefaction
by Nils Tellier, PE, President, EPSIM Corporation (CSA CSM) nils@epsim.us All illustrations courtesy EPSIM Corporation Background History of Air Separation and Liquefaction This section builds on a rich history of methods to develop deep refrigeration and cryogenic liquefaction during the 19th Century. You are encouraged to read Cryo Central’s History...
Bose-Einstein Condensate
A Bose-Einstein condensate, first proposed in 1925 by Albert Einstein based on work done by Satyendra Nath Bose (the same Bose from whom the term boson is derived), is a super-cold state of matter in which almost all of the individual atoms have “condensed” down to the lowest possible quantum...
Cold Technology for Pest Control
While it does not reach temperatures cold enough to be called cryogenic, carbon dioxide snow is at the heart of a new way of dealing with unwanted pests. It utilizes a quick freezing process that takes advantage of the properties of carbon dioxide snow and has a number of benefits...
Cryogenic Finishing
The following 3 articles discuss the uses and procedures of various type of cryogenic finishing. 1) By Robin A. Rhodes, Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Cryogenic Deflashing is employed to remove undesired residual mold flash that remains on molded parts after they are removed or ejected from the...
Reliability and mounting of electronic substrates at low temperatures
I am currently working on the design of a focal plane assembly to be implemented on a small satellite (4 EMCCD detectors) to be operated at -80°C (which is not really cryogenic and likely still considered boiling hot for most of you :-). As it is passively cooled, the assembly...
Are 3D drawings included in the sale of a cryogenic plant?
I have a question concerning the 3D drawings of a cryogenic plant. The integration of the 3D drawings of a plant with the 3D main model of a new laboratory or a new facility can be a complex work that takes a lot of time. I would like to know...
Looking for a source of LOX impact testing to ASTM D2512
I have been looking for a source of LOX impact testing to ASTM D2512. I am aware of NASA and White Sands, but am looking for a commercial entity doing the work. No luck so far, even calling a lot of the folks on the CSA website. Any referrals will...