VULCAN at SNS examines superconducting cables for ITER
The VULCAN Engineering Diffractometer at the Spallation Neutron Source is helping the ITER project with a very important task: investigating a problem within ITER's central solenoid magnet.
ADVERTISEMENT
Space shuttle Discovery to launch February 24
After several bumps in the road, the space shuttle Discovery is scheduled to launch on February 24 at 4:50 pm.
Tevatron to close at the end of FY2011
From Fermilab Today's Director's Corner: Yesterday we received the news that we will not receive funding for the proposed Tevatron extension and consequently the Tevatron will close at the end of FY2011 as was previously planned.
Praxair names new president of Praxair Distribution, Inc.
John Panikar has been named president of Praxair Distribution, Inc., the subsidiary of Praxair Inc. that manages the company's packaged gas business in the United States and Canada.
New study focuses on link between magnetism and superconductivity
Three decades of research have culminated in what researchers believe is the most convincing evidence yet for magnetism as the force that facilitates unconventional superconductivity.
ORNL scientists named APS fellows
Four scientists from Oak Ridge National Laboratory have been named fellows of the American Physical Society (APS): David Christen, David Geohegan, Xun-Li Wang and William Weber.
ADVERTISEMENT
Cold Compressors
A common way to provide cooling below the normal boiling point of helium (4.2K) is to reduce the pressure above the bath of liquid helium, thus also reducing the bath’s equilibrium saturation temperature. For example, to produce a 1.8K bath of liquid helium, the saturation pressure has to be reduced...
Kapitza Conductance
Kapitza conductance refers to the heat transfer between a solid surface and a fluid that covers that surface. Fundamentally, it describes the inherent difficulty in transferring energy from a solid to the fluid covering the solid surface. This phenomenon was first observed by P. L. Kapitza in 1941 while studying...
Thermosyphons
A thermosyphon (or thermosiphon) is a device that transfers heat via natural convection in a fluid. The natural convection is driven by gravity with the colder, denser fluid flowing downhill and the warmer, less dense fluid flowing back up. Thus, thermosyphons connect an object to be cooled with a reservoir...
Primary Standards
Elie K. Track Hypres, Inc. elie@hypres.com http://www.hypres.com/ Primary standards involve the exact definition and realization of units of measurement for various quantities, time, length, mass, voltage, resistance, current, etc. International agreements based on the latest scientific knowledge define those units, and their realizations vary depending on the unit itself. For...
Shrink Fitting
Robin A. Rhodes Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Shrink fitting, (or “compression fitting” as it is sometimes called), is a method used to insert a pin or bushing into a housing or other assembly requiring an extremely tight tolerance fit. It can be used as an alternative to...
Telecommunications
From the Winter 2004 issue of Cold Facts magazine The recent M-Calc IV — 4th Industry Assessment workshop discussing military and commercial applications for low-cost cryocoolers, held in November in San Diego, highlighted progress being made in cryogenics as applied in telecommunications. The reliability and long lifetime of projects now...
Wind Tunnels
Dr. Robert Kilgore The development of the cryogenic wind tunnel is one of many significant breakthroughs in both cryogenics and wind-tunnel technology made during the past millennium. Interest in the development of high-speed commercial and military aircraft resulted in a review of problems of flow simulation in transonic wind tunnels...
An Issue of Pressure and Flow Rate in a Supply Tank
Please help solve this problem: A supply tank requires a vaporizer to generate sufficient pressure to pump stored fluid up into a vehicle or tank. The available head is limited as the tank level falls and it is important to minimize the system pressure drop to maintain the desired flow...
Using MLI on VJ Line Joints or Cryo Storage Tanks
When installing Multi Layer Insulation (MLI) blankets on VJ line joints or cryo storage tanks should they be wrapped and tied down tight or loose? These are usually pre-cut to size. Also should they have an access hole at the point of where the molecular sieve is installed to help...
Separated layers of ice over a pipe
I want to know that why there are different layers of ice over a pipe carrying a cryogenic fluid, each layer separated with clear marks / lines? What do these layers signify?