Linde North America, a member of The Linde Group, has announced that Spectra Gases Inc., acquired in 2006, is changing its brand name to Linde, effective immediately.
Taylor Wharton International (TWI) has announced that it has filed "pre-arranged" voluntary Chapter 11 petitions in the United States Bankruptcy Court for the District of Delaware.
Fermilab Press Release, November 20, 2009: Particle beams are once again zooming around the world's most powerful particle accelerator-the Large Hadron Collider-located at the CERN laboratory near Geneva, Switzerland.
Paul Alivisatos was recently named director of Lawrence Berkeley National Laboratory after holding the position of interim director since January 2009.
Scientists from the Institute of Quantum Optics and Quantum Information recently won an international competition for producing a Bose-Einstein condensate of the alkaline-earth element strontium.
A dewar is a type of cryostat named after Sir James Dewar, the researcher who first developed the concept of a vacuum insulated container with silvered walls to reflect thermal radiation. Dewar was the first to liquefy hydrogen, and he created the device to store his discovery. The thermos bottle...
Stirling and Gifford-McMahon (GM) cryocoolers are two of the most commonly used cryocoolers in cryogenics. Both devices have a significant industrial base and operate at a wide range of temperatures and capacities. The thermodynamic cycles for both of these cryocoolers are quite similar. The Stirling cycle consists of a compressor,...
A significant commercial application of cryogenics is the liquefaction, transport and storage of natural gas. Liquefied Natural Gas (LNG) is generally 95 percent methane with a few percent ethane and much lower concentrations of propane and butane. LNG liquefies at 111.6 K. Unlike many applications of cryogenics, the motivation for...
Elie K. Track Hypres, Inc. elie@hypres.comhttp://www.hypres.com/ Primary standards involve the exact definition and realization of units of measurement for various quantities, time, length, mass, voltage, resistance, current, etc. International agreements based on the latest scientific knowledge define those units, and their realizations vary depending on the unit itself. For...
Robin A. Rhodes Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Shrink fitting, (or “compression fitting” as it is sometimes called), is a method used to insert a pin or bushing into a housing or other assembly requiring an extremely tight tolerance fit. It can be used as an alternative to...
From the Winter 2004 issue of Cold Facts magazine The recent M-Calc IV — 4th Industry Assessment workshop discussing military and commercial applications for low-cost cryocoolers, held in November in San Diego, highlighted progress being made in cryogenics as applied in telecommunications. The reliability and long lifetime of projects now...
Dr. Robert Kilgore The development of the cryogenic wind tunnel is one of many significant breakthroughs in both cryogenics and wind-tunnel technology made during the past millennium. Interest in the development of high-speed commercial and military aircraft resulted in a review of problems of flow simulation in transonic wind tunnels...
I was wondering if anyone could provide feedback/data on whether it is best in terms of preserving tissue quality to freeze tissue in OCT using dry ice versus liquid nitrogen?
We are a relatively new Biorepository that was developed as part of a large breast cancer epidemiology study, and thus far we have accumulated DNA on over 8000 women along with extensive questionnaire, mammography, and case status data. I was wondering, are there lists of existing Biorepositories with their contents?...
To size a relief valve for a LN2 cryostat I have to know “worse case” boil-off rate when vacuum insulation failed and inner vessel with LN2 is in direct contact with room temperature air at 300K. So, I am looking for a heat flux value (watt/m2) to LN2 inner vessel...
I am working on a project where we are trying to design a system to store ammonia at -33°C. In order to size the compressors to maintain the ammonia in the liquid state, I need to estimate the heat gained from the environment including the radiation from the sun and...