Groundbreaking ceremony held for new JLab upgrade
A groundbreaking ceremony was held on April 14 to mark the beginning of construction of Jefferson Lab's $310 million 12 GeV Upgrade project.
ADVERTISEMENT
The Daily Show visits CERN
The Daily Show visited CERN to unearth the truth behind the rumors that the world’s largest and most sophisticated science experiment will suck the Earth into a black hole.
Argonne to be home to new Energy Frontier Research Centers
President Barack Obama announced at the April 29 annual meeting of the National Academy of the Sciences that Argonne National Laboratory, a CSA Corporate Sustaining Member, is the site chosen for two new research centers.
John Stekly passed away April 3, 2009
Jon Stekly, member of the National Academy of Engineering, died April 3, 2009.
Fermilab ships completed 3.9GHz cryomodule to DESY
A cryomodule built at Fermilab for the free-electron laser FLASH at DESY arrived at the lab on Tuesday after travelling by road, air, road again and finally crane to its new home.
Praxair acquires three packaged gas companies
Praxair Distribution Inc., a subsidiary of Praxair, Inc., has acquired three packaged gas companies in the US.
ADVERTISEMENT
Regenerators
Regenerators or regenerative heat exchangers are a key component of cryocoolers such as pulse tube cryocoolers (Cold Facts, August 2014). Regenerator performance greatly affects the coefficient of performance of cryocoolers. Improvements in regenerator design and, in particular, regenerator materials have been an important factor in the improvement of the performance...
Pulse Tube Cryocoolers
The development of pulse tube cryocoolers has been a significant topic of research and development over the past 20 or so years. Pulse tube cryocoolers have a number of advantages over other types of cryocoolers and are now available commercially. In order to understand pulse tube cryocoolers, it’s best to...
Thermal Expansion
Thermal expansion refers to the change in size (length or volume) that a material undergoes as its temperature changes. In cryogenic systems this effect can be quite large and must be allowed for in the design. In isotropic materials, which include most engineering materials, the thermal expansion is the same...
Primary Standards
Elie K. Track Hypres, Inc. elie@hypres.com http://www.hypres.com/ Primary standards involve the exact definition and realization of units of measurement for various quantities, time, length, mass, voltage, resistance, current, etc. International agreements based on the latest scientific knowledge define those units, and their realizations vary depending on the unit itself. For...
Shrink Fitting
Robin A. Rhodes Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Shrink fitting, (or “compression fitting” as it is sometimes called), is a method used to insert a pin or bushing into a housing or other assembly requiring an extremely tight tolerance fit. It can be used as an alternative to...
Telecommunications
From the Winter 2004 issue of Cold Facts magazine The recent M-Calc IV — 4th Industry Assessment workshop discussing military and commercial applications for low-cost cryocoolers, held in November in San Diego, highlighted progress being made in cryogenics as applied in telecommunications. The reliability and long lifetime of projects now...
Wind Tunnels
Dr. Robert Kilgore The development of the cryogenic wind tunnel is one of many significant breakthroughs in both cryogenics and wind-tunnel technology made during the past millennium. Interest in the development of high-speed commercial and military aircraft resulted in a review of problems of flow simulation in transonic wind tunnels...
An Issue of Pressure and Flow Rate in a Supply Tank
Please help solve this problem: A supply tank requires a vaporizer to generate sufficient pressure to pump stored fluid up into a vehicle or tank. The available head is limited as the tank level falls and it is important to minimize the system pressure drop to maintain the desired flow...
Using MLI on VJ Line Joints or Cryo Storage Tanks
When installing Multi Layer Insulation (MLI) blankets on VJ line joints or cryo storage tanks should they be wrapped and tied down tight or loose? These are usually pre-cut to size. Also should they have an access hole at the point of where the molecular sieve is installed to help...
Separated layers of ice over a pipe
I want to know that why there are different layers of ice over a pipe carrying a cryogenic fluid, each layer separated with clear marks / lines? What do these layers signify?