CSA Announces Election Results
Elections for CSA President Elect and Directors as well as a vote on acceptance of the proposed amended CSA Constitution and Bylaws closed on August 8, 2008 at 12:00 pm.
ADVERTISEMENT
Hypres delivers Digital-RF (TM) receiver systems to ONR
Hypres Inc. has delivered two Digital-RF (TM) receiver systems to the U.S. Department of Defense's Office of Naval Research. The systems will serve as test beds to evaluate Digital-RF technology for wireless communications applications.
Zenergy announces extension of Rheinbach, Germany facility
Zenergy Power plc announced that it will expand its manufacturing facility based in Rheinbach, Germany, allowing the company to accommodate the expected increase in production of its ground-breaking HTS induction heater.
Synchronization of LHC beam transfer system a success
According to R&D Magazine, synchronization of the Large Hadron Collider's beam transfer system was shown to be successful through tests that began on August 8th. These preliminary tests are in preparation for the LHC's official first run on September 10, 2008, which will be webcast at webcast.cern.ch.
CSA Board Member George T. Mulholland dies
Longtime CSA Corporate Sustaining Member and Board Member and Secretary George T. Mulholland, 72, passed away Sunday, August 10, 2008 at Baylor Medical Center in Waxahachie, TX.
AMSC and US Navy test HTS degaussing system
American Superconductor announced that it has supplied critical components for a high-temperature superconductor degaussing coil system that will soon undergo US Navy sea trials.
ADVERTISEMENT
Joule-Thomson Effect
The Joule-Thomson (JT) effect is a thermodynamic process that occurs when a fluid expands from high pressure to low pressure at constant enthalpy (an isenthalpic process). Such a process can be approximated in the real world by expanding a fluid from high pressure to low pressure across a valve. Under...
Current Leads
One of the challenges of using superconducting magnets is the connection of the magnet to a room temperature power supply. This is accomplished via current leads. The trick is that current leads should ideally have a low heat leak, since they connect room temperature to cryogenic temperature, while at the...
Multilayer Insulation
Multilayer insulation (also referred to as superinsulation) is a key component in the reduction of heat leak to cryogenic systems due to thermal radiation. MLI consists of a series of uncooled reflective surfaces placed in the vacuum space between two surfaces, one warmer than the other. Generally speaking, for ideal...
Air Separation and Liquefaction
by Nils Tellier, PE, President, EPSIM Corporation (CSA CSM) nils@epsim.us All illustrations courtesy EPSIM Corporation Background History of Air Separation and Liquefaction This section builds on a rich history of methods to develop deep refrigeration and cryogenic liquefaction during the 19th Century. You are encouraged to read Cryo Central’s History...
Bose-Einstein Condensate
A Bose-Einstein condensate, first proposed in 1925 by Albert Einstein based on work done by Satyendra Nath Bose (the same Bose from whom the term boson is derived), is a super-cold state of matter in which almost all of the individual atoms have “condensed” down to the lowest possible quantum...
Cold Technology for Pest Control
While it does not reach temperatures cold enough to be called cryogenic, carbon dioxide snow is at the heart of a new way of dealing with unwanted pests. It utilizes a quick freezing process that takes advantage of the properties of carbon dioxide snow and has a number of benefits...
Cryogenic Finishing
The following 3 articles discuss the uses and procedures of various type of cryogenic finishing. 1) By Robin A. Rhodes, Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Cryogenic Deflashing is employed to remove undesired residual mold flash that remains on molded parts after they are removed or ejected from the...
Presence of alloying elements in tool steels
I want to expand my knowledge of cryogenics in general and tool steels in particular. Specifically, I am keenly interested in learning about the presence of alloying elements in tool steels and how their presence in various combinations affects the performance of tool steels after cryogenic treatment.
Pros and cons of barcoding samples
I was wondering if I could ask for input on pros and cons of barcoding. We are in the process of trying to decide if we should start barcoding our samples and I’m just not sure if this is feasible for our organization. We have numerous sites all over the...
Purity level of helium gas stream in cryo plant purification system
I would like to know what the principal methods and the relative instrumentation to check the purity level of helium gas stream in the purification system of a common helium cryogenic plant are. What principles are these instruments based on? And what are their principal characteristics?
LN2 for cryopreservation through controlled rate freezing of samples
I am the cryogenic specialist for a stem cell bank in Greece. I am trying to find the minimum requirements (purity, humidity, etc.) of liquid nitrogen for cryopreservation through controlled rate freezing of biological samples.