Cold Facts Digital – The go-to place for Cryogenics and Superconductivity

Looking to fabricate cast/electric HX

I am working on a project that involves the design, fabrication and location of vendors to fabricate a cast/electric HX that enables heating the propellant up from NBP, but won’t evaporate it. I am looking for assistance/advice.

Laboratories for Performing He4 Analysis Work

We are hoping to produce helium-4 with very low helium-3 contamination. Can you identify any laboratories that could assist in performing analysis work?

Grinding HNBR slab into 32-mesh powder

We have a small quantity to prove the feasibility of using HNBR slab ground into a small powder about 32 mesh or finer. Can you suggest an organization that can do this small quantity (about 1 or 2 lbs) and production quantities of a few hundred pounds?

Domestic companies that could cryogenically treat a tube?

Please identify some domestic companies that could cryogenically treat a tube.

Company to supply metallic recoated FBG sensor

I am studying FBG sensors for cryogenic temperature measurements. I am looking for a company that can supply me a metallic recoated FBG sensor. Please let me know if anybody has a contact.

What is cryotreatment or cryotempering?

Latest in Defining Cryogenics

Dilution Refrigerators

Dilution refrigerators are a common technique for reaching temperatures below 1K, particularly where continuous cooling at these temperatures is required. Helium exists in two stable isotopes: 4He and 3He. Naturally occurring 3He is extremely rare, constituting less than 1 part per million of helium gas. However, 3He can be manufactured,...

Oxygen Deficiency Hazards

Oxygen Deficiency Hazards (ODH) are a significant safety issue in cryogenic facilities. ODH occurs when inert gases such as nitrogen, helium or argon displace room air and thus lower the percentage of oxygen in the space below that required for human life. OSHA defines an area as oxygen deficient if...

Kelvin Temperature Scale

The Kelvin temperature scale is the principal temperature scale used in cryogenics and science. The kelvin is also one of the seven base units in the Système International d’Unités (SI) and is the unit of thermodynamic temperature. Thermodynamic temperature is a fundamental physical quantity (like mass, length or electrical current)...

Latest in Cryo Central

Primary Standards

Elie K. Track Hypres, Inc. elie@hypres.com http://www.hypres.com/ Primary standards involve the exact definition and realization of units of measurement for various quantities, time, length, mass, voltage, resistance, current, etc. International agreements based on the latest scientific knowledge define those units, and their realizations vary depending on the unit itself. For...

Shrink Fitting

Robin A. Rhodes Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Shrink fitting, (or “compression fitting” as it is sometimes called), is a method used to insert a pin or bushing into a housing or other assembly requiring an extremely tight tolerance fit. It can be used as an alternative to...

Telecommunications

From the Winter 2004 issue of Cold Facts magazine The recent M-Calc IV — 4th Industry Assessment workshop discussing military and commercial applications for low-cost cryocoolers, held in November in San Diego, highlighted progress being made in cryogenics as applied in telecommunications. The reliability and long lifetime of projects now...

Wind Tunnels

Dr. Robert Kilgore The development of the cryogenic wind tunnel is one of many significant breakthroughs in both cryogenics and wind-tunnel technology made during the past millennium. Interest in the development of high-speed commercial and military aircraft resulted in a review of problems of flow simulation in transonic wind tunnels...

Latest in Ask the Experts

An Issue of Pressure and Flow Rate in a Supply Tank

Please help solve this problem: A supply tank requires a vaporizer to generate sufficient pressure to pump stored fluid up into a vehicle or tank. The available head is limited as the tank level falls and it is important to minimize the system pressure drop to maintain the desired flow...

Using MLI on VJ Line Joints or Cryo Storage Tanks

When installing Multi Layer Insulation (MLI) blankets on VJ line joints or cryo storage tanks should they be wrapped and tied down tight or loose? These are usually pre-cut to size. Also should they have an access hole at the point of where the molecular sieve is installed to help...

Separated layers of ice over a pipe

I want to know that why there are different layers of ice over a pipe carrying a cryogenic fluid, each layer separated with clear marks / lines? What do these layers signify?

Using nitrogen as a cryogen

Is it possible to achieve -200˚C using nitrogen as a cryogen?

CATEGORIES