CSA Announces Election Results
Elections for CSA President Elect and Directors as well as a vote on acceptance of the proposed amended CSA Constitution and Bylaws closed on August 8, 2008 at 12:00 pm.
ADVERTISEMENT
Hypres delivers Digital-RF (TM) receiver systems to ONR
Hypres Inc. has delivered two Digital-RF (TM) receiver systems to the U.S. Department of Defense's Office of Naval Research. The systems will serve as test beds to evaluate Digital-RF technology for wireless communications applications.
Zenergy announces extension of Rheinbach, Germany facility
Zenergy Power plc announced that it will expand its manufacturing facility based in Rheinbach, Germany, allowing the company to accommodate the expected increase in production of its ground-breaking HTS induction heater.
Synchronization of LHC beam transfer system a success
According to R&D Magazine, synchronization of the Large Hadron Collider's beam transfer system was shown to be successful through tests that began on August 8th. These preliminary tests are in preparation for the LHC's official first run on September 10, 2008, which will be webcast at webcast.cern.ch.
CSA Board Member George T. Mulholland dies
Longtime CSA Corporate Sustaining Member and Board Member and Secretary George T. Mulholland, 72, passed away Sunday, August 10, 2008 at Baylor Medical Center in Waxahachie, TX.
AMSC and US Navy test HTS degaussing system
American Superconductor announced that it has supplied critical components for a high-temperature superconductor degaussing coil system that will soon undergo US Navy sea trials.
ADVERTISEMENT
Joule-Thomson Effect
The Joule-Thomson (JT) effect is a thermodynamic process that occurs when a fluid expands from high pressure to low pressure at constant enthalpy (an isenthalpic process). Such a process can be approximated in the real world by expanding a fluid from high pressure to low pressure across a valve. Under...
Current Leads
One of the challenges of using superconducting magnets is the connection of the magnet to a room temperature power supply. This is accomplished via current leads. The trick is that current leads should ideally have a low heat leak, since they connect room temperature to cryogenic temperature, while at the...
Multilayer Insulation
Multilayer insulation (also referred to as superinsulation) is a key component in the reduction of heat leak to cryogenic systems due to thermal radiation. MLI consists of a series of uncooled reflective surfaces placed in the vacuum space between two surfaces, one warmer than the other. Generally speaking, for ideal...
Air Separation and Liquefaction
by Nils Tellier, PE, President, EPSIM Corporation (CSA CSM) nils@epsim.us All illustrations courtesy EPSIM Corporation Background History of Air Separation and Liquefaction This section builds on a rich history of methods to develop deep refrigeration and cryogenic liquefaction during the 19th Century. You are encouraged to read Cryo Central’s History...
Bose-Einstein Condensate
A Bose-Einstein condensate, first proposed in 1925 by Albert Einstein based on work done by Satyendra Nath Bose (the same Bose from whom the term boson is derived), is a super-cold state of matter in which almost all of the individual atoms have “condensed” down to the lowest possible quantum...
Cold Technology for Pest Control
While it does not reach temperatures cold enough to be called cryogenic, carbon dioxide snow is at the heart of a new way of dealing with unwanted pests. It utilizes a quick freezing process that takes advantage of the properties of carbon dioxide snow and has a number of benefits...
Cryogenic Finishing
The following 3 articles discuss the uses and procedures of various type of cryogenic finishing. 1) By Robin A. Rhodes, Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Cryogenic Deflashing is employed to remove undesired residual mold flash that remains on molded parts after they are removed or ejected from the...
Manufacturer for a machine to liquefy natural gas or methane gas.
I’m in search of a company to manufacture a machine to liquefy natural gas or methane gas.
Need a plastic for diffuser on the magnet end of a LHe fill siphon
I am trying to select a plastic to be used as a diffuser on the magnet end of a LHe fill siphon. Can you recommend anything that will hold up at LHe temps? I have seen some and they look like HDPE or Polypropylene but I am not sure.
Thermal conductivity orthotropic properties from 300K up to 500K
I am looking for the thermal conductivity orthotropic properties from 300K up to 500K (or even higher, if available). “Cryocomp” provides orthotropic data on G-10 (Fill, Warp, Normal) only up to 300K.
Looking for heat conductivity values of CuCrZr in the low temperature range of 4 to 300K
I’m a student of physical engineering and I am looking for heat conductivity values of CuCrZr in the low temperature range of 4 to 300K. Jakub Voňka Brno University of Technology Faculty of Mechanical Engineering