CSA Announces Election Results
Elections for CSA President Elect and Directors as well as a vote on acceptance of the proposed amended CSA Constitution and Bylaws closed on August 8, 2008 at 12:00 pm.
ADVERTISEMENT
Hypres delivers Digital-RF (TM) receiver systems to ONR
Hypres Inc. has delivered two Digital-RF (TM) receiver systems to the U.S. Department of Defense's Office of Naval Research. The systems will serve as test beds to evaluate Digital-RF technology for wireless communications applications.
Zenergy announces extension of Rheinbach, Germany facility
Zenergy Power plc announced that it will expand its manufacturing facility based in Rheinbach, Germany, allowing the company to accommodate the expected increase in production of its ground-breaking HTS induction heater.
Synchronization of LHC beam transfer system a success
According to R&D Magazine, synchronization of the Large Hadron Collider's beam transfer system was shown to be successful through tests that began on August 8th. These preliminary tests are in preparation for the LHC's official first run on September 10, 2008, which will be webcast at webcast.cern.ch.
CSA Board Member George T. Mulholland dies
Longtime CSA Corporate Sustaining Member and Board Member and Secretary George T. Mulholland, 72, passed away Sunday, August 10, 2008 at Baylor Medical Center in Waxahachie, TX.
AMSC and US Navy test HTS degaussing system
American Superconductor announced that it has supplied critical components for a high-temperature superconductor degaussing coil system that will soon undergo US Navy sea trials.
ADVERTISEMENT
Joule-Thomson Effect
The Joule-Thomson (JT) effect is a thermodynamic process that occurs when a fluid expands from high pressure to low pressure at constant enthalpy (an isenthalpic process). Such a process can be approximated in the real world by expanding a fluid from high pressure to low pressure across a valve. Under...
Current Leads
One of the challenges of using superconducting magnets is the connection of the magnet to a room temperature power supply. This is accomplished via current leads. The trick is that current leads should ideally have a low heat leak, since they connect room temperature to cryogenic temperature, while at the...
Multilayer Insulation
Multilayer insulation (also referred to as superinsulation) is a key component in the reduction of heat leak to cryogenic systems due to thermal radiation. MLI consists of a series of uncooled reflective surfaces placed in the vacuum space between two surfaces, one warmer than the other. Generally speaking, for ideal...
Food Processing
Cryogenics and Food The industrial gas industry provides a host of products and services related to food. The various gases have useful and sometimes fascinating applications in food industry. “The food industry is not a homogenous industry. The needs of customers processing hamburger vs. poultry vs. strawberries vs. seafood, for...
Primary Standards
Elie K. Track Hypres, Inc. elie@hypres.com http://www.hypres.com/ Primary standards involve the exact definition and realization of units of measurement for various quantities, time, length, mass, voltage, resistance, current, etc. International agreements based on the latest scientific knowledge define those units, and their realizations vary depending on the unit itself. For...
Shrink Fitting
Robin A. Rhodes Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Shrink fitting, (or “compression fitting” as it is sometimes called), is a method used to insert a pin or bushing into a housing or other assembly requiring an extremely tight tolerance fit. It can be used as an alternative to...
Telecommunications
From the Winter 2004 issue of Cold Facts magazine The recent M-Calc IV — 4th Industry Assessment workshop discussing military and commercial applications for low-cost cryocoolers, held in November in San Diego, highlighted progress being made in cryogenics as applied in telecommunications. The reliability and long lifetime of projects now...
An Issue of Pressure and Flow Rate in a Supply Tank
Please help solve this problem: A supply tank requires a vaporizer to generate sufficient pressure to pump stored fluid up into a vehicle or tank. The available head is limited as the tank level falls and it is important to minimize the system pressure drop to maintain the desired flow...
Using MLI on VJ Line Joints or Cryo Storage Tanks
When installing Multi Layer Insulation (MLI) blankets on VJ line joints or cryo storage tanks should they be wrapped and tied down tight or loose? These are usually pre-cut to size. Also should they have an access hole at the point of where the molecular sieve is installed to help...
Separated layers of ice over a pipe
I want to know that why there are different layers of ice over a pipe carrying a cryogenic fluid, each layer separated with clear marks / lines? What do these layers signify?