Cold Facts Digital – The go-to place for Cryogenics and Superconductivity

Standards for fabrication of vessels/tanks?

I’m a total novice in the design and manufacture of cryogenic equipment, but nonetheless I’m a pressure vessel Designer/Engineer. Could you possibly advise as to any relevant standards/documentation that may be available with regard to, in particular, the fabrication of vessels/tanks?

Manufacturers of pressure regulators—liquid argon

I am trying to locate companies that manufacture and sell pressure regulators rated for dispensing liquid argon for a welding application. Do you know of companies that I could contact with this request?

Effect of heat treat temper on aluminum at cryo temps?

What effect does heat treat temper have on aluminum at cryo temps?

Looking to fabricate cast/electric HX

I am working on a project that involves the design, fabrication and location of vendors to fabricate a cast/electric HX that enables heating the propellant up from NBP, but won’t evaporate it. I am looking for assistance/advice.

Laboratories for Performing He4 Analysis Work

We are hoping to produce helium-4 with very low helium-3 contamination. Can you identify any laboratories that could assist in performing analysis work?

Grinding HNBR slab into 32-mesh powder

We have a small quantity to prove the feasibility of using HNBR slab ground into a small powder about 32 mesh or finer. Can you suggest an organization that can do this small quantity (about 1 or 2 lbs) and production quantities of a few hundred pounds?

Latest in Defining Cryogenics

Joule-Thomson Effect

The Joule-Thomson (JT) effect is a thermodynamic process that occurs when a fluid expands from high pressure to low pressure at constant enthalpy (an isenthalpic process). Such a process can be approximated in the real world by expanding a fluid from high pressure to low pressure across a valve. Under...

Current Leads

One of the challenges of using superconducting magnets is the connection of the magnet to a room temperature power supply. This is accomplished via current leads. The trick is that current leads should ideally have a low heat leak, since they connect room temperature to cryogenic temperature, while at the...

Multilayer Insulation

Multilayer insulation (also referred to as superinsulation) is a key component in the reduction of heat leak to cryogenic systems due to thermal radiation. MLI consists of a series of uncooled reflective surfaces placed in the vacuum space between two surfaces, one warmer than the other. Generally speaking, for ideal...

Latest in Cryo Central

Air Separation and Liquefaction

by Nils Tellier, PE, President, EPSIM Corporation (CSA CSM) nils@epsim.us All illustrations courtesy EPSIM Corporation Background History of Air Separation and Liquefaction This section builds on a rich history of methods to develop deep refrigeration and cryogenic liquefaction during the 19th Century. You are encouraged to read Cryo Central’s History...

Bose-Einstein Condensate

A Bose-Einstein condensate, first proposed in 1925 by Albert Einstein based on work done by Satyendra Nath Bose (the same Bose from whom the term boson is derived), is a super-cold state of matter in which almost all of the individual atoms have “condensed” down to the lowest possible quantum...

Cold Technology for Pest Control

While it does not reach temperatures cold enough to be called cryogenic, carbon dioxide snow is at the heart of a new way of dealing with unwanted pests. It utilizes a quick freezing process that takes advantage of the properties of carbon dioxide snow and has a number of benefits...

Cryogenic Finishing

The following 3 articles discuss the uses and procedures of various type of cryogenic finishing. 1) By Robin A. Rhodes, Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Cryogenic Deflashing is employed to remove undesired residual mold flash that remains on molded parts after they are removed or ejected from the...

Latest in Ask the Experts

Resistance to embrittlement at low temperatures

Could anyone advise me about resistance to embrittlement at low temperatures for the alloys in subject, i.e. does the CF10M perform like the CF8M in the same cryogenic service (-215F)? Amara Maafi Amara.Maafi@bg-group.com

Need help with temperature dependent model

I am a fourth-year student at New Zealand University. My name is Xu Ke. I have a project to generate a temperature dependent model for inductor, capacitor and diode by using PLECS. PLECS is software which acts as a toolbox for MATLAB. In my models, the temperature is very low,...

In what form is water available in LN2?

Does anybody know in what form water is available in LN2? There probably is a block of ice in the bottom of the tank. But as water comes in many shapes, I can imagine snow or crystals floating free in the LN2. When water is available in LN2, could small...

Separating gases using cryogenics

We are looking for some consulting engineers who understand how to separate gases using cryogenics. We have a new process which takes biomass and converts it to 5 gases and we need to separate these gases into their pure forms. Thanks for your help. Malcolm Draper Energy Research Group LLC...

CATEGORIES