MicroBooNE begins construction, elects co-spokesperson
Fermilab's neutrino experiment, MicroBooNE, is beginning the full construction phase for the detector, after DOE announced the official Critical Decision 3b approval on March 29.
ADVERTISEMENT
CLNG president responds to senator’s comments on LNG exports
In response to comments from U.S. Sen. Ron Wyden suggesting the United States needs a policy on energy exports and that a "timeout" should be declared on permits to export LNG to non-Free Trade Agreement countries, Center for Liquefied Natural Gas (CLNG) President Bill Cooper issued the following statement:
Linde introduces new N2 pressure booster
Gas-assist injection molders (GAIM) can improve efficiency and quality -- even on lightweight parts and difficult geometries -- with the help of a new liquid nitrogen (N2) pressure booster from Linde North America.
Argonne named a “Best Place” for postdocs to work
For postdoctoral scholars, or postdocs, Argonne National Laboratory is the 6th best place to work in the United States, according to The Scientist, a life sciences magazine.
At DOE, body blows to fusion, nuclear physics and particle physics
Overall, the 2013 budget numbers for the Department of Energy's (DOE's) Office of Science, the single largest funder of physical sciences research in the United States, look reasonably good. The office would see its budget climb by 2.4% to $4.992 billion. Three of the office's six major research programs, however,...
CERN experiment makes spectroscopic measurement of antihydrogen
In a paper published online on March 7 by the journal Nature, the ALPHA collaboration at CERN reports an important milestone on the way to measuring the properties of antimatter atoms.
ADVERTISEMENT
Stability
Stability refers to the ability of a device employing superconductors to remain in its superconducting state after part of the superconductor transitions back to its normal conducting state due to a disturbance. While the concept can apply to many superconducting devices—transmission lines, generators, motors, etc.—it is most commonly considered in...
Cable-in-Conduit Conductors
Cable-in-Conduit Conductors (CICC) are a common form of superconducting cable used in large-scale applications. There are several varieties of CICCs, but they all consist of many small, stabilized superconducting wires contained within a conduit through which a coolant (typically supercritical He II) flows. Figure 1 shows the cross section of...
Bayonet Coupling
A bayonet coupling is a demountable joint that allows for quick and easy connection and disconnection of cryogenic components, including transfer lines, cryostats, liquefiers and refrigerators. Bayonets provide a number of advantages, chief among them the ability to connect and disconnect the bayonets while components they connect are still at...
Air Separation and Liquefaction
by Nils Tellier, PE, President, EPSIM Corporation (CSA CSM) nils@epsim.us All illustrations courtesy EPSIM Corporation Background History of Air Separation and Liquefaction This section builds on a rich history of methods to develop deep refrigeration and cryogenic liquefaction during the 19th Century. You are encouraged to read Cryo Central’s History...
Bose-Einstein Condensate
A Bose-Einstein condensate, first proposed in 1925 by Albert Einstein based on work done by Satyendra Nath Bose (the same Bose from whom the term boson is derived), is a super-cold state of matter in which almost all of the individual atoms have “condensed” down to the lowest possible quantum...
Cold Technology for Pest Control
While it does not reach temperatures cold enough to be called cryogenic, carbon dioxide snow is at the heart of a new way of dealing with unwanted pests. It utilizes a quick freezing process that takes advantage of the properties of carbon dioxide snow and has a number of benefits...
Cryogenic Finishing
The following 3 articles discuss the uses and procedures of various type of cryogenic finishing. 1) By Robin A. Rhodes, Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Cryogenic Deflashing is employed to remove undesired residual mold flash that remains on molded parts after they are removed or ejected from the...
Where can the cryogenic insulator trade be studied?
I have been searching for information regarding the training of cryogenic insulators and have not been able to find any information in North America.
Material Selection and Testing For the Magnet Wire
I am looking for some help in material selection for the magnet wire (CDA101 oxygen-free copper, phosphor bronze, beryllium copper, others?) and insulation materials. Also, what testing is required to establish the RRR for any particular wire?
Density and/or elasticity at temps from 170 K down to 70 K
I have been searching [unsuccessfully] for data on both the elasticity and density figures for 316 st/steel at low temperatures.
Aluminum-stainless steel transitions
I am looking for a Al-SS transition pieces that will allow welding between aluminum and stainless steel tubes. Do you know a supplier of these transitions?