MicroBooNE begins construction, elects co-spokesperson
Fermilab's neutrino experiment, MicroBooNE, is beginning the full construction phase for the detector, after DOE announced the official Critical Decision 3b approval on March 29.
ADVERTISEMENT
CLNG president responds to senator’s comments on LNG exports
In response to comments from U.S. Sen. Ron Wyden suggesting the United States needs a policy on energy exports and that a "timeout" should be declared on permits to export LNG to non-Free Trade Agreement countries, Center for Liquefied Natural Gas (CLNG) President Bill Cooper issued the following statement:
Linde introduces new N2 pressure booster
Gas-assist injection molders (GAIM) can improve efficiency and quality -- even on lightweight parts and difficult geometries -- with the help of a new liquid nitrogen (N2) pressure booster from Linde North America.
Argonne named a “Best Place” for postdocs to work
For postdoctoral scholars, or postdocs, Argonne National Laboratory is the 6th best place to work in the United States, according to The Scientist, a life sciences magazine.
At DOE, body blows to fusion, nuclear physics and particle physics
Overall, the 2013 budget numbers for the Department of Energy's (DOE's) Office of Science, the single largest funder of physical sciences research in the United States, look reasonably good. The office would see its budget climb by 2.4% to $4.992 billion. Three of the office's six major research programs, however,...
CERN experiment makes spectroscopic measurement of antihydrogen
In a paper published online on March 7 by the journal Nature, the ALPHA collaboration at CERN reports an important milestone on the way to measuring the properties of antimatter atoms.
ADVERTISEMENT
Joule-Thomson Effect
The Joule-Thomson (JT) effect is a thermodynamic process that occurs when a fluid expands from high pressure to low pressure at constant enthalpy (an isenthalpic process). Such a process can be approximated in the real world by expanding a fluid from high pressure to low pressure across a valve. Under...
Current Leads
One of the challenges of using superconducting magnets is the connection of the magnet to a room temperature power supply. This is accomplished via current leads. The trick is that current leads should ideally have a low heat leak, since they connect room temperature to cryogenic temperature, while at the...
Multilayer Insulation
Multilayer insulation (also referred to as superinsulation) is a key component in the reduction of heat leak to cryogenic systems due to thermal radiation. MLI consists of a series of uncooled reflective surfaces placed in the vacuum space between two surfaces, one warmer than the other. Generally speaking, for ideal...
Air Separation and Liquefaction
by Nils Tellier, PE, President, EPSIM Corporation (CSA CSM) nils@epsim.us All illustrations courtesy EPSIM Corporation Background History of Air Separation and Liquefaction This section builds on a rich history of methods to develop deep refrigeration and cryogenic liquefaction during the 19th Century. You are encouraged to read Cryo Central’s History...
Bose-Einstein Condensate
A Bose-Einstein condensate, first proposed in 1925 by Albert Einstein based on work done by Satyendra Nath Bose (the same Bose from whom the term boson is derived), is a super-cold state of matter in which almost all of the individual atoms have “condensed” down to the lowest possible quantum...
Cold Technology for Pest Control
While it does not reach temperatures cold enough to be called cryogenic, carbon dioxide snow is at the heart of a new way of dealing with unwanted pests. It utilizes a quick freezing process that takes advantage of the properties of carbon dioxide snow and has a number of benefits...
Cryogenic Finishing
The following 3 articles discuss the uses and procedures of various type of cryogenic finishing. 1) By Robin A. Rhodes, Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Cryogenic Deflashing is employed to remove undesired residual mold flash that remains on molded parts after they are removed or ejected from the...
Need help comparing chest freezers and upright freezers
Currently we use in our Biobank an upright -80 freezer to store all our samples. We are planning to buy a fully automated bio-repository storage that will do the picking of samples under restricted conditions. But in the meantime I foresee that we have to pick the samples manually. The...
Need recommendations for cryogenic vials
I am looking into standardizing our range of bio storage tubes (cryogenic vials). These will be for both blood and tissue samples and their derivatives. Any recommendations, comments on Micronics, Nalgene, Nunc and or others that are suitable for long term -80 C and -196 C storage, DNA/RNA suitable, would...
We need a custom machine for flash freezing of water
We are an ice making company and have started a new project, which is related to flash freezing of water. It is based on cryogenics technology and we need a custom made machine. I would kindly ask you to pass me a few companies who would be interested in such...
Looking for a pump suitable for cold liquids
I would like to construct a small cooling circuit (appr. 50 x 50 cm) pumping liquid at a temperature down to -120°C from a cold reservoir to the specimen to be cooled. The tubes and connections are not a problem, but does somebody know a pump (suction/compression for circulation) suitable...