TWI appoints Bill Corbin as Interim CEO
Bill Corbin, a current Board Member in the Board of Directors at Taylor-Wharton International, LLC (TWI), has been appointed Chairman and Interim Chief Executive Officer.
ADVERTISEMENT
NASA awards LN2 and LOX contracts
Linde LLC, Air Products and Chemicals, Inc. and Air Liquide Industrial have all been awarded contracts to supply liquid nitrogen and liquid oxygen to six NASA facilities.
NIU’s proton center to miss deadline for completion
The $159 million cancer treatment center planned at Northern Illinois University will almost certainly miss the March 2010 completion date, a date that was required by the state when the project was approved.
Full Interviews from Industrial Gas Manufacturers
The Spring 2009 issue of Cold Facts featured interviews from leaders in the industrial gases industry. Here are the interviews in their entirety, including information about each company's background and additional comments provided during the interview.
Airgas Gaspro celebrates centenary
From gasworld, June 2009: Airgas Gaspro, a business unit of Airgas, Inc., is celebrating 100 years in the Hawaiian community.
Technex delivers cryogenic tank semi-trailer to Iceblick
Technex Limited, a manufacturer of cryogenic tank semi-trailers for transporting liquid gases and liquid natural gas (LNG), has successfully completed the delivery of a cryogenic tank semi-trailer to Iceblick, a manufacturer and supplier of rare and industrial gases.
ADVERTISEMENT
Stability
Stability refers to the ability of a device employing superconductors to remain in its superconducting state after part of the superconductor transitions back to its normal conducting state due to a disturbance. While the concept can apply to many superconducting devices—transmission lines, generators, motors, etc.—it is most commonly considered in...
Cable-in-Conduit Conductors
Cable-in-Conduit Conductors (CICC) are a common form of superconducting cable used in large-scale applications. There are several varieties of CICCs, but they all consist of many small, stabilized superconducting wires contained within a conduit through which a coolant (typically supercritical He II) flows. Figure 1 shows the cross section of...
Bayonet Coupling
A bayonet coupling is a demountable joint that allows for quick and easy connection and disconnection of cryogenic components, including transfer lines, cryostats, liquefiers and refrigerators. Bayonets provide a number of advantages, chief among them the ability to connect and disconnect the bayonets while components they connect are still at...
Primary Standards
Elie K. Track Hypres, Inc. elie@hypres.com http://www.hypres.com/ Primary standards involve the exact definition and realization of units of measurement for various quantities, time, length, mass, voltage, resistance, current, etc. International agreements based on the latest scientific knowledge define those units, and their realizations vary depending on the unit itself. For...
Shrink Fitting
Robin A. Rhodes Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Shrink fitting, (or “compression fitting” as it is sometimes called), is a method used to insert a pin or bushing into a housing or other assembly requiring an extremely tight tolerance fit. It can be used as an alternative to...
Telecommunications
From the Winter 2004 issue of Cold Facts magazine The recent M-Calc IV — 4th Industry Assessment workshop discussing military and commercial applications for low-cost cryocoolers, held in November in San Diego, highlighted progress being made in cryogenics as applied in telecommunications. The reliability and long lifetime of projects now...
Wind Tunnels
Dr. Robert Kilgore The development of the cryogenic wind tunnel is one of many significant breakthroughs in both cryogenics and wind-tunnel technology made during the past millennium. Interest in the development of high-speed commercial and military aircraft resulted in a review of problems of flow simulation in transonic wind tunnels...
An Issue of Pressure and Flow Rate in a Supply Tank
Please help solve this problem: A supply tank requires a vaporizer to generate sufficient pressure to pump stored fluid up into a vehicle or tank. The available head is limited as the tank level falls and it is important to minimize the system pressure drop to maintain the desired flow...
Using MLI on VJ Line Joints or Cryo Storage Tanks
When installing Multi Layer Insulation (MLI) blankets on VJ line joints or cryo storage tanks should they be wrapped and tied down tight or loose? These are usually pre-cut to size. Also should they have an access hole at the point of where the molecular sieve is installed to help...
Separated layers of ice over a pipe
I want to know that why there are different layers of ice over a pipe carrying a cryogenic fluid, each layer separated with clear marks / lines? What do these layers signify?