ADVERTISEMENT
New method shows electron pairs precede HTS
Using new imaging methods, scientists at Brookhaven National Laboratory have confirmed that electron pairs that carry electrical current emerge above the transition temperature before superconductivity sets in.
Organizations urge Obama to appoint White House Science Advisor
The American Institute of Physics, the American Physical Society and the American Astronomical Society were among 180 organizations that signed letters to President-Elect Barack Obama and Senator John McCain, urging them to appoint a White House Science Advisor by Inauguration Day.
PBS’ Independent Lens to air “The Atom Smashers” on Nov.25
On Tuesday, November 25, 2008 at 10:30 PM CST, PBS's Independent Lens will air a documentary called "The Atom Smashers." The film gives an in-depth look into particle physics, the Fermilab Tevatron, CERN's Large Hadron Collider and the search for the Higgs boson.
Request for Assistance: Cryogenic MEMS Pressure Sensor
I am working on a National Science Foundation grant with researchers from Silicon Valley to develop a new type of MEMS pressure sensor. Given my background in cryogenics I was wondering if it could be adapted to that environment and am exploring research opportunities. Initial thoughts are to develop a...
Professor Haruyama named Chairman of ICEC
Longtime CSA Member Professor Tomiyoshi Haruyama of the Institute of Particle and Nuclear Studies at KEK has been named Chairman of the International Cryogenic Engineering Conference Committee.
ADVERTISEMENT
Cold Compressors
A common way to provide cooling below the normal boiling point of helium (4.2K) is to reduce the pressure above the bath of liquid helium, thus also reducing the bath’s equilibrium saturation temperature. For example, to produce a 1.8K bath of liquid helium, the saturation pressure has to be reduced...
Kapitza Conductance
Kapitza conductance refers to the heat transfer between a solid surface and a fluid that covers that surface. Fundamentally, it describes the inherent difficulty in transferring energy from a solid to the fluid covering the solid surface. This phenomenon was first observed by P. L. Kapitza in 1941 while studying...
Thermosyphons
A thermosyphon (or thermosiphon) is a device that transfers heat via natural convection in a fluid. The natural convection is driven by gravity with the colder, denser fluid flowing downhill and the warmer, less dense fluid flowing back up. Thus, thermosyphons connect an object to be cooled with a reservoir...
Air Separation and Liquefaction
by Nils Tellier, PE, President, EPSIM Corporation (CSA CSM) nils@epsim.us All illustrations courtesy EPSIM Corporation Background History of Air Separation and Liquefaction This section builds on a rich history of methods to develop deep refrigeration and cryogenic liquefaction during the 19th Century. You are encouraged to read Cryo Central’s History...
Bose-Einstein Condensate
A Bose-Einstein condensate, first proposed in 1925 by Albert Einstein based on work done by Satyendra Nath Bose (the same Bose from whom the term boson is derived), is a super-cold state of matter in which almost all of the individual atoms have “condensed” down to the lowest possible quantum...
Cold Technology for Pest Control
While it does not reach temperatures cold enough to be called cryogenic, carbon dioxide snow is at the heart of a new way of dealing with unwanted pests. It utilizes a quick freezing process that takes advantage of the properties of carbon dioxide snow and has a number of benefits...
Cryogenic Finishing
The following 3 articles discuss the uses and procedures of various type of cryogenic finishing. 1) By Robin A. Rhodes, Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Cryogenic Deflashing is employed to remove undesired residual mold flash that remains on molded parts after they are removed or ejected from the...
Reliability and mounting of electronic substrates at low temperatures
I am currently working on the design of a focal plane assembly to be implemented on a small satellite (4 EMCCD detectors) to be operated at -80°C (which is not really cryogenic and likely still considered boiling hot for most of you :-). As it is passively cooled, the assembly...
Are 3D drawings included in the sale of a cryogenic plant?
I have a question concerning the 3D drawings of a cryogenic plant. The integration of the 3D drawings of a plant with the 3D main model of a new laboratory or a new facility can be a complex work that takes a lot of time. I would like to know...
Looking for a source of LOX impact testing to ASTM D2512
I have been looking for a source of LOX impact testing to ASTM D2512. I am aware of NASA and White Sands, but am looking for a commercial entity doing the work. No luck so far, even calling a lot of the folks on the CSA website. Any referrals will...