CSA Announces Election Results
Elections for CSA President Elect and Directors as well as a vote on acceptance of the proposed amended CSA Constitution and Bylaws closed on August 8, 2008 at 12:00 pm.
ADVERTISEMENT
Hypres delivers Digital-RF (TM) receiver systems to ONR
Hypres Inc. has delivered two Digital-RF (TM) receiver systems to the U.S. Department of Defense's Office of Naval Research. The systems will serve as test beds to evaluate Digital-RF technology for wireless communications applications.
Zenergy announces extension of Rheinbach, Germany facility
Zenergy Power plc announced that it will expand its manufacturing facility based in Rheinbach, Germany, allowing the company to accommodate the expected increase in production of its ground-breaking HTS induction heater.
Synchronization of LHC beam transfer system a success
According to R&D Magazine, synchronization of the Large Hadron Collider's beam transfer system was shown to be successful through tests that began on August 8th. These preliminary tests are in preparation for the LHC's official first run on September 10, 2008, which will be webcast at webcast.cern.ch.
CSA Board Member George T. Mulholland dies
Longtime CSA Corporate Sustaining Member and Board Member and Secretary George T. Mulholland, 72, passed away Sunday, August 10, 2008 at Baylor Medical Center in Waxahachie, TX.
AMSC and US Navy test HTS degaussing system
American Superconductor announced that it has supplied critical components for a high-temperature superconductor degaussing coil system that will soon undergo US Navy sea trials.
ADVERTISEMENT
Regenerators
Regenerators or regenerative heat exchangers are a key component of cryocoolers such as pulse tube cryocoolers (Cold Facts, August 2014). Regenerator performance greatly affects the coefficient of performance of cryocoolers. Improvements in regenerator design and, in particular, regenerator materials have been an important factor in the improvement of the performance...
Pulse Tube Cryocoolers
The development of pulse tube cryocoolers has been a significant topic of research and development over the past 20 or so years. Pulse tube cryocoolers have a number of advantages over other types of cryocoolers and are now available commercially. In order to understand pulse tube cryocoolers, it’s best to...
Thermal Expansion
Thermal expansion refers to the change in size (length or volume) that a material undergoes as its temperature changes. In cryogenic systems this effect can be quite large and must be allowed for in the design. In isotropic materials, which include most engineering materials, the thermal expansion is the same...
Air Separation and Liquefaction
by Nils Tellier, PE, President, EPSIM Corporation (CSA CSM) nils@epsim.us All illustrations courtesy EPSIM Corporation Background History of Air Separation and Liquefaction This section builds on a rich history of methods to develop deep refrigeration and cryogenic liquefaction during the 19th Century. You are encouraged to read Cryo Central’s History...
Bose-Einstein Condensate
A Bose-Einstein condensate, first proposed in 1925 by Albert Einstein based on work done by Satyendra Nath Bose (the same Bose from whom the term boson is derived), is a super-cold state of matter in which almost all of the individual atoms have “condensed” down to the lowest possible quantum...
Cold Technology for Pest Control
While it does not reach temperatures cold enough to be called cryogenic, carbon dioxide snow is at the heart of a new way of dealing with unwanted pests. It utilizes a quick freezing process that takes advantage of the properties of carbon dioxide snow and has a number of benefits...
Cryogenic Finishing
The following 3 articles discuss the uses and procedures of various type of cryogenic finishing. 1) By Robin A. Rhodes, Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Cryogenic Deflashing is employed to remove undesired residual mold flash that remains on molded parts after they are removed or ejected from the...
Low temperature applications of titanium and alloys
For a technical presentation I would like to have some recommendations for low temperature applications of titanium and titanium alloys. Do you think you can help me?
Designing a liquid oxygen bath
I’m designing a Liquid Oxygen Bath to place composite coupons in the bath and soak 96 samples for intervals of 8 hours, 24 hours, 7 days, 21 days, 42 days, 62 days and 90 days.
School science projects involving cryogenics and metallurgy?
Can you recommend any school science projects that would involve cryogenics and metallurgy?
Metallic Salts Normally Used to Produce Ultra-Low Temperatures?
Regarding the method known as the Adiabatic Demagnetization of Paramagnetic Salts: What metallic salts are normally used to produce the ultra-low temperatures used for near-absolute-zero cryogenic research? Which salts are the most efficient? Which make the best cooling agents? And which are used most commonly by physicists? I am looking...