Cold Facts Digital – The go-to place for Cryogenics and Superconductivity

Synchronization of LHC beam transfer system a success

According to R&D Magazine, synchronization of the Large Hadron Collider's beam transfer system was shown to be successful through tests that began on August 8th. These preliminary tests are in preparation for the LHC's official first run on September 10, 2008, which will be webcast at webcast.cern.ch.

CSA Board Member George T. Mulholland dies

Longtime CSA Corporate Sustaining Member and Board Member and Secretary George T. Mulholland, 72, passed away Sunday, August 10, 2008 at Baylor Medical Center in Waxahachie, TX.

AMSC and US Navy test HTS degaussing system

American Superconductor announced that it has supplied critical components for a high-temperature superconductor degaussing coil system that will soon undergo US Navy sea trials.

Standards for fabrication of vessels/tanks?

I’m a total novice in the design and manufacture of cryogenic equipment, but nonetheless I’m a pressure vessel Designer/Engineer. Could you possibly advise as to any relevant standards/documentation that may be available with regard to, in particular, the fabrication of vessels/tanks?

Manufacturers of pressure regulators—liquid argon

I am trying to locate companies that manufacture and sell pressure regulators rated for dispensing liquid argon for a welding application. Do you know of companies that I could contact with this request?

Effect of heat treat temper on aluminum at cryo temps?

What effect does heat treat temper have on aluminum at cryo temps?

Latest in Defining Cryogenics

Helium-3

Helium-3 (3He) is one of the two stable isotopes of helium. The other is the much more common Helium-4 (4He). Neither of these isotopes should be confused with He II, which is the second liquid phase of 4He. He II was discussed in this column in the Spring 2010 edition...

Cryopumping

Cryopumping refers to the use of cryogenic temperatures to produce vacuum in enclosed spaces. More broadly, it can also refer to the removal of gases via cryogenic temperatures from a flow stream or enclosure without necessarily resulting in vacuum pressures. This is an important application of cryogenics and is used...

Thermal Acoustic Oscillations

Thermal Acoustic Oscillations (TAO) are a common event in cryogenic systems that can have significant adverse effects on the performance of the system. TAOs are sustained pressure oscillations that can occur in tubes containing gas, closed at one end (the warm end) that have a very large temperature gradient along...

Latest in Cryo Central

Air Separation and Liquefaction

by Nils Tellier, PE, President, EPSIM Corporation (CSA CSM) nils@epsim.us All illustrations courtesy EPSIM Corporation Background History of Air Separation and Liquefaction This section builds on a rich history of methods to develop deep refrigeration and cryogenic liquefaction during the 19th Century. You are encouraged to read Cryo Central’s History...

Bose-Einstein Condensate

A Bose-Einstein condensate, first proposed in 1925 by Albert Einstein based on work done by Satyendra Nath Bose (the same Bose from whom the term boson is derived), is a super-cold state of matter in which almost all of the individual atoms have “condensed” down to the lowest possible quantum...

Cold Technology for Pest Control

While it does not reach temperatures cold enough to be called cryogenic, carbon dioxide snow is at the heart of a new way of dealing with unwanted pests. It utilizes a quick freezing process that takes advantage of the properties of carbon dioxide snow and has a number of benefits...

Cryogenic Finishing

The following 3 articles discuss the uses and procedures of various type of cryogenic finishing. 1) By Robin A. Rhodes, Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Cryogenic Deflashing is employed to remove undesired residual mold flash that remains on molded parts after they are removed or ejected from the...

Latest in Ask the Experts

An Issue of Pressure and Flow Rate in a Supply Tank

Please help solve this problem: A supply tank requires a vaporizer to generate sufficient pressure to pump stored fluid up into a vehicle or tank. The available head is limited as the tank level falls and it is important to minimize the system pressure drop to maintain the desired flow...

Using MLI on VJ Line Joints or Cryo Storage Tanks

When installing Multi Layer Insulation (MLI) blankets on VJ line joints or cryo storage tanks should they be wrapped and tied down tight or loose? These are usually pre-cut to size. Also should they have an access hole at the point of where the molecular sieve is installed to help...

Separated layers of ice over a pipe

I want to know that why there are different layers of ice over a pipe carrying a cryogenic fluid, each layer separated with clear marks / lines? What do these layers signify?

Using nitrogen as a cryogen

Is it possible to achieve -200˚C using nitrogen as a cryogen?

CATEGORIES