Category: Ask the Experts

I'm in search of a company to manufacture a machine to liquefy natural gas or methane gas.

I am trying to select a plastic to be used as a diffuser on the magnet end of a LHe fill siphon. Can you recommend anything that will hold up at LHe temps? I have seen some and they look like HDPE or Polypropylene but I am not sure.

I am looking for the thermal conductivity orthotropic properties from 300K up to 500K (or even higher, if available). "Cryocomp" provides orthotropic data on G-10 (Fill, Warp, Normal) only up to 300K.

I'm a student of physical engineering and I am looking for heat conductivity values of CuCrZr in the low temperature range of 4 to 300K. Jakub Voňka Brno University of Technology Faculty of Mechanical Engineering

Would you know of a technical publication that would list the benefits and explain the science behind the cryogenic treatment of aluminum, specifically a 356-T6 aluminum cylinder head casting? Eddie Phillips

Can anyone recommend a source of emissivity data for aluminum and aluminized Mylar at room temperature, 77K and 4.2K? Also, I would be interested in finding a facility that can measure this information. Any information will be greatly appreciated. William Einziger, GE Healthcare

I will be purchasing a new liquid nitrogen freezer soon, but I am limited by space restrictions. The freezer cannot be more than 38 inches wide. However, it would be beneficial if the freezer holds a high number of racks such as 24. In addition, we prefer not to purchase …

I am trying to find out if anyone knows of or has used an affordable flow meter that can measure liquid nitrogen flow through a pipeline. It doesn’t need to be very accurate as it’s really to allow people in different departments to allocate cost rather than for scientific measurement. …

I am looking for the thermal conductivity of the high density polyethylene (HDPE) between 1.9 and 10K (or even up to higher temperatures). The best would be to have these data for the HDPE material which sold by the CERN shop, which has a density of 0.95 g/cm3. Pier Paolo …

Can somebody please tell me what the “Alpha Cryogenic Process” is? How is it different from ordinary cryogenic processing? Bernd Ahne, HiFi-Tuning

I was just wondering, do Stirling coolers have any relation to Stirling engines?

I work for ASRC Aerospace at the Kennedy Space Center (KSC). We support NASA in ground support equipment (GSE) design. I have a question concerning the type of multilayer insulation (MLI) to use in LOX vacuum Jacketed (VJ) lines and flex hoses.

My company is going to create a cryogenic engineering department and we need some books in order to facilitate this project. This is the kind of information we would like to obtain from the books: 1- Calculations for determining the storage facilities, such as storage tanks, pumps, compressors, etc. 2- …

We have a picture where the various layers of a transfer line are labeled.

I am a graduate student in the Dept. of Mechanical Engineering at West Virginia University. As a part of my research, I'm doing a case study of design of a Cryogenic Pressure Vessel. I'm facing a little difficulty in the process, and would be very grateful to you if you …

What's the difference between a cryocooler and a cryostat?

Could anyone advise me about resistance to embrittlement at low temperatures for the alloys in subject, i.e. does the CF10M perform like the CF8M in the same cryogenic service (-215F)? Amara Maafi Amara.Maafi@bg-group.com

I am a fourth-year student at New Zealand University. My name is Xu Ke. I have a project to generate a temperature dependent model for inductor, capacitor and diode by using PLECS. PLECS is software which acts as a toolbox for MATLAB. In my models, the temperature is very low, …

Does anybody know in what form water is available in LN2? There probably is a block of ice in the bottom of the tank. But as water comes in many shapes, I can imagine snow or crystals floating free in the LN2. When water is available in LN2, could small …

We are looking for some consulting engineers who understand how to separate gases using cryogenics. We have a new process which takes biomass and converts it to 5 gases and we need to separate these gases into their pure forms. Thanks for your help. Malcolm Draper Energy Research Group LLC …