ADVERTISEMENT
Luisa Chiesa receives early career award from DOE
Luisa Chiesa, assistant professor in mechanical engineering at Tufts School of Engineering, has been chosen to receive an early career award from the US Department of Energy.
Ability Engineering receives award from UT-Battelle
Ability Engineering Technology has been recognized by UT-Battelle, LLC, management and operating contractor for Oak Ridge National Laboratory.
Alcor involved in dispute over woman’s head
Alcor Life Extension in Scottsdale AZ is at the heart of another cryonics battle.
Alain Ravex starts new consultant role
Dr. Alain Ravex has left his position as Development, Technology and Innovation Director at Air Liquide Advanced Technology Division and is now an independent consultant in cryogenics.
Barbie starts new career as Computer Engineer
A half million Barbie fans participated in a vote to choose the doll’s next career: Computer Engineer.
ADVERTISEMENT
Dewar
A dewar is a type of cryostat named after Sir James Dewar, the researcher who first developed the concept of a vacuum insulated container with silvered walls to reflect thermal radiation. Dewar was the first to liquefy hydrogen, and he created the device to store his discovery. The thermos bottle...
Stirling and Gifford-McMahon Cryocoolers
Stirling and Gifford-McMahon (GM) cryocoolers are two of the most commonly used cryocoolers in cryogenics. Both devices have a significant industrial base and operate at a wide range of temperatures and capacities. The thermodynamic cycles for both of these cryocoolers are quite similar. The Stirling cycle consists of a compressor,...
Liquefied Natural Gas (LNG)
A significant commercial application of cryogenics is the liquefaction, transport and storage of natural gas. Liquefied Natural Gas (LNG) is generally 95 percent methane with a few percent ethane and much lower concentrations of propane and butane. LNG liquefies at 111.6 K. Unlike many applications of cryogenics, the motivation for...
Air Separation and Liquefaction
by Nils Tellier, PE, President, EPSIM Corporation (CSA CSM) nils@epsim.us All illustrations courtesy EPSIM Corporation Background History of Air Separation and Liquefaction This section builds on a rich history of methods to develop deep refrigeration and cryogenic liquefaction during the 19th Century. You are encouraged to read Cryo Central’s History...
Bose-Einstein Condensate
A Bose-Einstein condensate, first proposed in 1925 by Albert Einstein based on work done by Satyendra Nath Bose (the same Bose from whom the term boson is derived), is a super-cold state of matter in which almost all of the individual atoms have “condensed” down to the lowest possible quantum...
Cold Technology for Pest Control
While it does not reach temperatures cold enough to be called cryogenic, carbon dioxide snow is at the heart of a new way of dealing with unwanted pests. It utilizes a quick freezing process that takes advantage of the properties of carbon dioxide snow and has a number of benefits...
Cryogenic Finishing
The following 3 articles discuss the uses and procedures of various type of cryogenic finishing. 1) By Robin A. Rhodes, Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Cryogenic Deflashing is employed to remove undesired residual mold flash that remains on molded parts after they are removed or ejected from the...
An Issue of Pressure and Flow Rate in a Supply Tank
Please help solve this problem: A supply tank requires a vaporizer to generate sufficient pressure to pump stored fluid up into a vehicle or tank. The available head is limited as the tank level falls and it is important to minimize the system pressure drop to maintain the desired flow...
Using MLI on VJ Line Joints or Cryo Storage Tanks
When installing Multi Layer Insulation (MLI) blankets on VJ line joints or cryo storage tanks should they be wrapped and tied down tight or loose? These are usually pre-cut to size. Also should they have an access hole at the point of where the molecular sieve is installed to help...
Separated layers of ice over a pipe
I want to know that why there are different layers of ice over a pipe carrying a cryogenic fluid, each layer separated with clear marks / lines? What do these layers signify?