Cold Facts Digital – Page 61 – The go-to place for Cryogenics and Superconductivity

Standards for fabrication of vessels/tanks?

I’m a total novice in the design and manufacture of cryogenic equipment, but nonetheless I’m a pressure vessel Designer/Engineer. Could you possibly advise as to any relevant standards/documentation that may be available with regard to, in particular, the fabrication of vessels/tanks?

Manufacturers of pressure regulators—liquid argon

I am trying to locate companies that manufacture and sell pressure regulators rated for dispensing liquid argon for a welding application. Do you know of companies that I could contact with this request?

Effect of heat treat temper on aluminum at cryo temps?

What effect does heat treat temper have on aluminum at cryo temps?

Looking to fabricate cast/electric HX

I am working on a project that involves the design, fabrication and location of vendors to fabricate a cast/electric HX that enables heating the propellant up from NBP, but won’t evaporate it. I am looking for assistance/advice.

Laboratories for Performing He4 Analysis Work

We are hoping to produce helium-4 with very low helium-3 contamination. Can you identify any laboratories that could assist in performing analysis work?

Grinding HNBR slab into 32-mesh powder

We have a small quantity to prove the feasibility of using HNBR slab ground into a small powder about 32 mesh or finer. Can you suggest an organization that can do this small quantity (about 1 or 2 lbs) and production quantities of a few hundred pounds?

Latest in Defining Cryogenics

Transfer Lines

Transfer lines may in some real sense be thought of as the cryogenic fluid analogy of current leads. While current leads carry electrical power to where it’s required in a cryogenic system, transfer lines do the same with cryogenic fluids. Transfer lines range in complexity from very simple U-tubes containing...

Zero Boiloff

Zero Boil Off cryostats are those that contain liquid cryogens but are designed to eliminate or vastly reduce the boil off of the liquid. These cryostats combine some of the advantages of Cryogen-Free systems (e.g. ease of use and long operational lifetime) with the advantages associated with a reservoir of liquid...

Cryomodule

Cryomodule is a term that is most commonly used to refer to cryostats that contain superconducting radio frequency (SRF) cavities. Such cavities are used to accelerate charged particle beams and are a major component of modern particle accelerators. Using the term cryomodule to refer to cryostats containing SRF cavities appears...

Latest in Cryo Central

Food Processing

Cryogenics and Food The industrial gas industry provides a host of products and services related to food. The various gases have useful and sometimes fascinating applications in food industry. “The food industry is not a homogenous industry. The needs of customers processing hamburger vs. poultry vs. strawberries vs. seafood, for...

Primary Standards

Elie K. Track Hypres, Inc. elie@hypres.com http://www.hypres.com/ Primary standards involve the exact definition and realization of units of measurement for various quantities, time, length, mass, voltage, resistance, current, etc. International agreements based on the latest scientific knowledge define those units, and their realizations vary depending on the unit itself. For...

Shrink Fitting

Robin A. Rhodes Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Shrink fitting, (or “compression fitting” as it is sometimes called), is a method used to insert a pin or bushing into a housing or other assembly requiring an extremely tight tolerance fit. It can be used as an alternative to...

Telecommunications

From the Winter 2004 issue of Cold Facts magazine The recent M-Calc IV — 4th Industry Assessment workshop discussing military and commercial applications for low-cost cryocoolers, held in November in San Diego, highlighted progress being made in cryogenics as applied in telecommunications. The reliability and long lifetime of projects now...

Latest in Ask the Experts

An Issue of Pressure and Flow Rate in a Supply Tank

Please help solve this problem: A supply tank requires a vaporizer to generate sufficient pressure to pump stored fluid up into a vehicle or tank. The available head is limited as the tank level falls and it is important to minimize the system pressure drop to maintain the desired flow...

Using MLI on VJ Line Joints or Cryo Storage Tanks

When installing Multi Layer Insulation (MLI) blankets on VJ line joints or cryo storage tanks should they be wrapped and tied down tight or loose? These are usually pre-cut to size. Also should they have an access hole at the point of where the molecular sieve is installed to help...

Separated layers of ice over a pipe

I want to know that why there are different layers of ice over a pipe carrying a cryogenic fluid, each layer separated with clear marks / lines? What do these layers signify?

Using nitrogen as a cryogen

Is it possible to achieve -200˚C using nitrogen as a cryogen?

CATEGORIES