Peter Kittel’s “Intro to Pulse Tube Thermodynamics” featured in Cold Facts
The first part of Dr. Peter Kittel's "Introduction to Pulse Tube Thermodynamics" was featured in the Fall 2012 issue of Cold Facts, which will be available for download soon.
ADVERTISEMENT
Dr. Joel Ullom receives CSA’s Roger W. Boom Award
Dr. Joel Ullom, 2012 CSA Roger W. Boom awardee, is the NIST Project Leader for superconducting calorimeter development and has worked in the fields of low temperature sensors, low temperature electronics and cryogenic systems since 1994.
Chemical synthesis achieves superconductivity at 44K
Physicists describe how they have synthesized a new material that belongs to the iron-selenide class of superconductors, called LixFe2Se2(NH3)y, in a paper about to be published in EPJ B. The work was carried out by Ernst-Wilhelm Scheidt from the University of Augsburg and colleagues.
CSA announces 2012 election results
CSA recently announced the results of the 2012 Board of Technical Directors election. The results were certified at CSA's board meeting at the Applied Superconductivity Conference in Portland OR.
NASA worker not fired over intelligent design, judge says
A California judge has tentatively ruled that a worker fired from NASA's Jet Propulsion Laboratory did not lose his job over his intelligent design beliefs.
Air Products licenses cryogenic machining technology to MAG IAS
Air Products has licensed its proprietary cryogenic machining technology to MAG IAS, LLC, a leading machine tool manufacturer.
ADVERTISEMENT
Dilution Refrigerators
Dilution refrigerators are a common technique for reaching temperatures below 1K, particularly where continuous cooling at these temperatures is required. Helium exists in two stable isotopes: 4He and 3He. Naturally occurring 3He is extremely rare, constituting less than 1 part per million of helium gas. However, 3He can be manufactured,...
Oxygen Deficiency Hazards
Oxygen Deficiency Hazards (ODH) are a significant safety issue in cryogenic facilities. ODH occurs when inert gases such as nitrogen, helium or argon displace room air and thus lower the percentage of oxygen in the space below that required for human life. OSHA defines an area as oxygen deficient if...
Kelvin Temperature Scale
The Kelvin temperature scale is the principal temperature scale used in cryogenics and science. The kelvin is also one of the seven base units in the Système International d’Unités (SI) and is the unit of thermodynamic temperature. Thermodynamic temperature is a fundamental physical quantity (like mass, length or electrical current)...
Air Separation and Liquefaction
by Nils Tellier, PE, President, EPSIM Corporation (CSA CSM) nils@epsim.us All illustrations courtesy EPSIM Corporation Background History of Air Separation and Liquefaction This section builds on a rich history of methods to develop deep refrigeration and cryogenic liquefaction during the 19th Century. You are encouraged to read Cryo Central’s History...
Bose-Einstein Condensate
A Bose-Einstein condensate, first proposed in 1925 by Albert Einstein based on work done by Satyendra Nath Bose (the same Bose from whom the term boson is derived), is a super-cold state of matter in which almost all of the individual atoms have “condensed” down to the lowest possible quantum...
Cold Technology for Pest Control
While it does not reach temperatures cold enough to be called cryogenic, carbon dioxide snow is at the heart of a new way of dealing with unwanted pests. It utilizes a quick freezing process that takes advantage of the properties of carbon dioxide snow and has a number of benefits...
Cryogenic Finishing
The following 3 articles discuss the uses and procedures of various type of cryogenic finishing. 1) By Robin A. Rhodes, Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Cryogenic Deflashing is employed to remove undesired residual mold flash that remains on molded parts after they are removed or ejected from the...
Information about a process called “cryogenically stretch-formed ss”
I am remembering in the 1970’s when astronauts were walking on the moon and carried oxygen in 300 ss bottles inside LN2 tanks which were filled and pressurized.
Small cryo-gun for our health service clinic
I am Assistant Director for Environmental Health & Safety at a university health service clinic.
Additional sealing materials besides PTFE or glass filled PTFE
I am an engineer looking to improve our solenoid valve sealing on cryogenic medias. I was wondering if you knew of materials other then PTFE or glass filled PTFE that could be used for sealing.
What is the temperature range of cryogenics?
Could you please tell me what is the temperature range of cryogenics? In other words, is -100°F considered cryogenic, or does it start lower? Could I expect to see some extended life in D2 stamping dies? What would the recipe be to achieve the desired results using cryogenics?