Oxford Instruments achieves 22.07 Tesla in a SC magnet
CSA Corporate Sustaining Member Oxford Instruments announced that it has achieved 22.07 Tesla in a fully superconducting magnet operating at 4.2K.
ADVERTISEMENT
Barish to be next VP of APS
ILC GDE Director Barry Barish has been chosen as the next Vice President of the American Physical Society (APS) beginning in January 2009; he will become President-Elect in 2010, and President in 2011.
LHC rap gains popularity on YouTube.com
Kate McAlpine’s Large Hadron Collider rap has become extremely popular on YouTube.com, where the video has gotten over 3.5 million views. (“LHC rap”)
Dryogenic, Ltd. to deliver low-temperature system to S. Korea
Dryogenic Ltd. has announced that it will deliver and install the first cryogen-free low temperature system to Kookmin University in Seoul, South Korea.
Rising helium prices affect ballooning sport
gasworld reports on the impact that the helium shortage has had on helium ballooning as an adventure sport.
3-D MRI studied by Canadian researchers
A study conducted by Canadian researchers at the Sunnybrook Health Sciences Center in Toronto has shown that three-dimensional magnetic resonance imaging (3-D MRI) can accurately detect bleeding within the walls of diseased carotid arteries.
ADVERTISEMENT
Dilution Refrigerators
Dilution refrigerators are a common technique for reaching temperatures below 1K, particularly where continuous cooling at these temperatures is required. Helium exists in two stable isotopes: 4He and 3He. Naturally occurring 3He is extremely rare, constituting less than 1 part per million of helium gas. However, 3He can be manufactured,...
Oxygen Deficiency Hazards
Oxygen Deficiency Hazards (ODH) are a significant safety issue in cryogenic facilities. ODH occurs when inert gases such as nitrogen, helium or argon displace room air and thus lower the percentage of oxygen in the space below that required for human life. OSHA defines an area as oxygen deficient if...
Kelvin Temperature Scale
The Kelvin temperature scale is the principal temperature scale used in cryogenics and science. The kelvin is also one of the seven base units in the Système International d’Unités (SI) and is the unit of thermodynamic temperature. Thermodynamic temperature is a fundamental physical quantity (like mass, length or electrical current)...
Air Separation and Liquefaction
by Nils Tellier, PE, President, EPSIM Corporation (CSA CSM) nils@epsim.us All illustrations courtesy EPSIM Corporation Background History of Air Separation and Liquefaction This section builds on a rich history of methods to develop deep refrigeration and cryogenic liquefaction during the 19th Century. You are encouraged to read Cryo Central’s History...
Bose-Einstein Condensate
A Bose-Einstein condensate, first proposed in 1925 by Albert Einstein based on work done by Satyendra Nath Bose (the same Bose from whom the term boson is derived), is a super-cold state of matter in which almost all of the individual atoms have “condensed” down to the lowest possible quantum...
Cold Technology for Pest Control
While it does not reach temperatures cold enough to be called cryogenic, carbon dioxide snow is at the heart of a new way of dealing with unwanted pests. It utilizes a quick freezing process that takes advantage of the properties of carbon dioxide snow and has a number of benefits...
Cryogenic Finishing
The following 3 articles discuss the uses and procedures of various type of cryogenic finishing. 1) By Robin A. Rhodes, Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Cryogenic Deflashing is employed to remove undesired residual mold flash that remains on molded parts after they are removed or ejected from the...
An Issue of Pressure and Flow Rate in a Supply Tank
Please help solve this problem: A supply tank requires a vaporizer to generate sufficient pressure to pump stored fluid up into a vehicle or tank. The available head is limited as the tank level falls and it is important to minimize the system pressure drop to maintain the desired flow...
Using MLI on VJ Line Joints or Cryo Storage Tanks
When installing Multi Layer Insulation (MLI) blankets on VJ line joints or cryo storage tanks should they be wrapped and tied down tight or loose? These are usually pre-cut to size. Also should they have an access hole at the point of where the molecular sieve is installed to help...
Separated layers of ice over a pipe
I want to know that why there are different layers of ice over a pipe carrying a cryogenic fluid, each layer separated with clear marks / lines? What do these layers signify?