Cold Facts Digital – The go-to place for Cryogenics and Superconductivity

Manufacturers of pressure regulators—liquid argon

I am trying to locate companies that manufacture and sell pressure regulators rated for dispensing liquid argon for a welding application. Do you know of companies that I could contact with this request?

Effect of heat treat temper on aluminum at cryo temps?

What effect does heat treat temper have on aluminum at cryo temps?

Looking to fabricate cast/electric HX

I am working on a project that involves the design, fabrication and location of vendors to fabricate a cast/electric HX that enables heating the propellant up from NBP, but won’t evaporate it. I am looking for assistance/advice.

Laboratories for Performing He4 Analysis Work

We are hoping to produce helium-4 with very low helium-3 contamination. Can you identify any laboratories that could assist in performing analysis work?

Grinding HNBR slab into 32-mesh powder

We have a small quantity to prove the feasibility of using HNBR slab ground into a small powder about 32 mesh or finer. Can you suggest an organization that can do this small quantity (about 1 or 2 lbs) and production quantities of a few hundred pounds?

Domestic companies that could cryogenically treat a tube?

Please identify some domestic companies that could cryogenically treat a tube.

Latest in Defining Cryogenics

Dewar

A dewar is a type of cryostat named after Sir James Dewar, the researcher who first developed the concept of a vacuum insulated container with silvered walls to reflect thermal radiation. Dewar was the first to liquefy hydrogen, and he created the device to store his discovery. The thermos bottle...

Stirling and Gifford-McMahon Cryocoolers

Stirling and Gifford-McMahon (GM) cryocoolers are two of the most commonly used cryocoolers in cryogenics. Both devices have a significant industrial base and operate at a wide range of temperatures and capacities. The thermodynamic cycles for both of these cryocoolers are quite similar. The Stirling cycle consists of a compressor,...

Liquefied Natural Gas (LNG)

A significant commercial application of cryogenics is the liquefaction, transport and storage of natural gas. Liquefied Natural Gas (LNG) is generally 95 percent methane with a few percent ethane and much lower concentrations of propane and butane. LNG liquefies at 111.6 K. Unlike many applications of cryogenics, the motivation for...

Latest in Cryo Central

Primary Standards

Elie K. Track Hypres, Inc. elie@hypres.com http://www.hypres.com/ Primary standards involve the exact definition and realization of units of measurement for various quantities, time, length, mass, voltage, resistance, current, etc. International agreements based on the latest scientific knowledge define those units, and their realizations vary depending on the unit itself. For...

Shrink Fitting

Robin A. Rhodes Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Shrink fitting, (or “compression fitting” as it is sometimes called), is a method used to insert a pin or bushing into a housing or other assembly requiring an extremely tight tolerance fit. It can be used as an alternative to...

Telecommunications

From the Winter 2004 issue of Cold Facts magazine The recent M-Calc IV — 4th Industry Assessment workshop discussing military and commercial applications for low-cost cryocoolers, held in November in San Diego, highlighted progress being made in cryogenics as applied in telecommunications. The reliability and long lifetime of projects now...

Wind Tunnels

Dr. Robert Kilgore The development of the cryogenic wind tunnel is one of many significant breakthroughs in both cryogenics and wind-tunnel technology made during the past millennium. Interest in the development of high-speed commercial and military aircraft resulted in a review of problems of flow simulation in transonic wind tunnels...

Latest in Ask the Experts

Low temperature applications of titanium and alloys

For a technical presentation I would like to have some recommendations for low temperature applications of titanium and titanium alloys. Do you think you can help me?

Designing a liquid oxygen bath

I’m designing a Liquid Oxygen Bath to place composite coupons in the bath and soak 96 samples for intervals of 8 hours, 24 hours, 7 days, 21 days, 42 days, 62 days and 90 days.

School science projects involving cryogenics and metallurgy?

Can you recommend any school science projects that would involve cryogenics and metallurgy?

Metallic Salts Normally Used to Produce Ultra-Low Temperatures?

Regarding the method known as the Adiabatic Demagnetization of Paramagnetic Salts: What metallic salts are normally used to produce the ultra-low temperatures used for near-absolute-zero cryogenic research? Which salts are the most efficient? Which make the best cooling agents? And which are used most commonly by physicists? I am looking...

CATEGORIES