NASA has announced that its newest observatory, the Gamma-Ray Large Area Space Telescope, or GLAST, has been renamed the Fermi Gamma-Ray Space Telescope, in honor of Professor Enrico Fermi (1901-1954).
Elections for CSA President Elect and Directors as well as a vote on acceptance of the proposed amended CSA Constitution and Bylaws closed on August 8, 2008 at 12:00 pm.
Hypres Inc. has delivered two Digital-RF (TM) receiver systems to the U.S. Department of Defense's Office of Naval Research. The systems will serve as test beds to evaluate Digital-RF technology for wireless communications applications.
Zenergy Power plc announced that it will expand its manufacturing facility based in Rheinbach, Germany, allowing the company to accommodate the expected increase in production of its ground-breaking HTS induction heater.
According to R&D Magazine, synchronization of the Large Hadron Collider's beam transfer system was shown to be successful through tests that began on August 8th. These preliminary tests are in preparation for the LHC's official first run on September 10, 2008, which will be webcast at webcast.cern.ch.
Longtime CSA Corporate Sustaining Member and Board Member and Secretary George T. Mulholland, 72, passed away Sunday, August 10, 2008 at Baylor Medical Center in Waxahachie, TX.
A dewar is a type of cryostat named after Sir James Dewar, the researcher who first developed the concept of a vacuum insulated container with silvered walls to reflect thermal radiation. Dewar was the first to liquefy hydrogen, and he created the device to store his discovery. The thermos bottle...
Stirling and Gifford-McMahon (GM) cryocoolers are two of the most commonly used cryocoolers in cryogenics. Both devices have a significant industrial base and operate at a wide range of temperatures and capacities. The thermodynamic cycles for both of these cryocoolers are quite similar. The Stirling cycle consists of a compressor,...
A significant commercial application of cryogenics is the liquefaction, transport and storage of natural gas. Liquefied Natural Gas (LNG) is generally 95 percent methane with a few percent ethane and much lower concentrations of propane and butane. LNG liquefies at 111.6 K. Unlike many applications of cryogenics, the motivation for...
Randall Kirschman, consulting physicist, Mountain View, California ExtElect@gmail.com Cryogenic electronics—the operation of electronic devices, circuits, and systems at cryogenic temperatures—has been a valuable technology for decades. Cryogenic electronics (also referred to as low-temperature electronics, or cold electronics) can be based on semiconductive devices, on superconductive devices, or on a combination...
Cryogenics and High-Energy Physics 1. From symmetry magazine: http://www.symmetrymagazine.org/cms/?pid=1000627: Cryogenics is the study of how materials behave at temperatures near absolute zero. In high-energy particle accelerators, such frigid temperatures reduce the electrical resistance of wires in superconducting magnets, increasing the magnet strength and allowing faster particle acceleration. The same holds...
From the Spring 2009 issue of Cold Facts (Volume 25, Number 2): Thanks to a joint project by the US Navy and a number of industry partners, high temperature superconducting (HTS) technology is now at the heart of an advanced degaussing system aboard the USS Higgins at the naval station...
From http://www.superconductors.org: An area where superconductors can perform a life-saving function is in the field of biomagnetism. Doctors need a non-invasive means of determining what’s going on inside the human body. By impinging a strong superconductor-derived magnetic field into the body, hydrogen atoms that exist in the body’s water and...
Greetings from Australia. I am looking for a company that I might contact that has any experience or has done any research into cryogenic processing for medical equipment, in particular, joint prosthesis.
I’m on the hunt for a material/gel/epoxy that will transfer the cold temperature of a cryo-box to a test article. The cryo-box is curved and the test article is at the same curvature. I’m looking for something to put between them to make the surface of the test article as...
I’m seeking a consultant with experience in the manufacture of brazed aluminum heat exchangers for cryogenic applications. Is there anyone you could recommend to me?