Fermilab's neutrino experiment, MicroBooNE, is beginning the full construction phase for the detector, after DOE announced the official Critical Decision 3b approval on March 29.
In response to comments from U.S. Sen. Ron Wyden suggesting the United States needs a policy on energy exports and that a "timeout" should be declared on permits to export LNG to non-Free Trade Agreement countries, Center for Liquefied Natural Gas (CLNG) President Bill Cooper issued the following statement:
Gas-assist injection molders (GAIM) can improve efficiency and quality -- even on lightweight parts and difficult geometries -- with the help of a new liquid nitrogen (N2) pressure booster from Linde North America.
For postdoctoral scholars, or postdocs, Argonne National Laboratory is the 6th best place to work in the United States, according to The Scientist, a life sciences magazine.
Overall, the 2013 budget numbers for the Department of Energy's (DOE's) Office of Science, the single largest funder of physical sciences research in the United States, look reasonably good. The office would see its budget climb by 2.4% to $4.992 billion. Three of the office's six major research programs, however,...
In a paper published online on March 7 by the journal Nature, the ALPHA collaboration at CERN reports an important milestone on the way to measuring the properties of antimatter atoms.
Reaching temperatures below 1K requires different techniques than the various helium gas cycles found in large scale refrigeration plants and small cryocoolers. One of these techniques is Adiabatic Demagnetization Refrigeration (ADR). This technique takes advantage of the fact that the entropy of paramagnetic materials in a magnetic field is lower than...
A cryogen is any fluid that operates at cryogenic temperatures (below roughly 150K – 120K). Using this definition, helium gas at 40K is a cryogen. Another more restrictive definition is to use cryogen to refer specifically to liquids at cryogenic temperatures. This is generally how it is used in the...
A cryostat is any device designed to maintain things (including fluids) at cryogenic temperatures. In general usage, cryostats tend to be passive devices rather than providing active cooling. In this usage, cryostats keep things cold by thermally isolating them from room temperature. This generally is accomplished by a combination of...
Randall Kirschman, consulting physicist, Mountain View, California ExtElect@gmail.com Cryogenic electronics—the operation of electronic devices, circuits, and systems at cryogenic temperatures—has been a valuable technology for decades. Cryogenic electronics (also referred to as low-temperature electronics, or cold electronics) can be based on semiconductive devices, on superconductive devices, or on a combination...
Cryogenics and High-Energy Physics 1. From symmetry magazine: http://www.symmetrymagazine.org/cms/?pid=1000627: Cryogenics is the study of how materials behave at temperatures near absolute zero. In high-energy particle accelerators, such frigid temperatures reduce the electrical resistance of wires in superconducting magnets, increasing the magnet strength and allowing faster particle acceleration. The same holds...
From the Spring 2009 issue of Cold Facts (Volume 25, Number 2): Thanks to a joint project by the US Navy and a number of industry partners, high temperature superconducting (HTS) technology is now at the heart of an advanced degaussing system aboard the USS Higgins at the naval station...
From http://www.superconductors.org: An area where superconductors can perform a life-saving function is in the field of biomagnetism. Doctors need a non-invasive means of determining what’s going on inside the human body. By impinging a strong superconductor-derived magnetic field into the body, hydrogen atoms that exist in the body’s water and...
Please help solve this problem: A supply tank requires a vaporizer to generate sufficient pressure to pump stored fluid up into a vehicle or tank. The available head is limited as the tank level falls and it is important to minimize the system pressure drop to maintain the desired flow...
When installing Multi Layer Insulation (MLI) blankets on VJ line joints or cryo storage tanks should they be wrapped and tied down tight or loose? These are usually pre-cut to size. Also should they have an access hole at the point of where the molecular sieve is installed to help...
I want to know that why there are different layers of ice over a pipe carrying a cryogenic fluid, each layer separated with clear marks / lines? What do these layers signify?