Oxford Instruments achieves 22.07 Tesla in a SC magnet
CSA Corporate Sustaining Member Oxford Instruments announced that it has achieved 22.07 Tesla in a fully superconducting magnet operating at 4.2K.
ADVERTISEMENT
Barish to be next VP of APS
ILC GDE Director Barry Barish has been chosen as the next Vice President of the American Physical Society (APS) beginning in January 2009; he will become President-Elect in 2010, and President in 2011.
LHC rap gains popularity on YouTube.com
Kate McAlpine’s Large Hadron Collider rap has become extremely popular on YouTube.com, where the video has gotten over 3.5 million views. (“LHC rap”)
Dryogenic, Ltd. to deliver low-temperature system to S. Korea
Dryogenic Ltd. has announced that it will deliver and install the first cryogen-free low temperature system to Kookmin University in Seoul, South Korea.
Rising helium prices affect ballooning sport
gasworld reports on the impact that the helium shortage has had on helium ballooning as an adventure sport.
3-D MRI studied by Canadian researchers
A study conducted by Canadian researchers at the Sunnybrook Health Sciences Center in Toronto has shown that three-dimensional magnetic resonance imaging (3-D MRI) can accurately detect bleeding within the walls of diseased carotid arteries.
ADVERTISEMENT
Regenerators
Regenerators or regenerative heat exchangers are a key component of cryocoolers such as pulse tube cryocoolers (Cold Facts, August 2014). Regenerator performance greatly affects the coefficient of performance of cryocoolers. Improvements in regenerator design and, in particular, regenerator materials have been an important factor in the improvement of the performance...
Pulse Tube Cryocoolers
The development of pulse tube cryocoolers has been a significant topic of research and development over the past 20 or so years. Pulse tube cryocoolers have a number of advantages over other types of cryocoolers and are now available commercially. In order to understand pulse tube cryocoolers, it’s best to...
Thermal Expansion
Thermal expansion refers to the change in size (length or volume) that a material undergoes as its temperature changes. In cryogenic systems this effect can be quite large and must be allowed for in the design. In isotropic materials, which include most engineering materials, the thermal expansion is the same...
Primary Standards
Elie K. Track Hypres, Inc. elie@hypres.com http://www.hypres.com/ Primary standards involve the exact definition and realization of units of measurement for various quantities, time, length, mass, voltage, resistance, current, etc. International agreements based on the latest scientific knowledge define those units, and their realizations vary depending on the unit itself. For...
Shrink Fitting
Robin A. Rhodes Cryogenic Institute of New England, Inc. rrhodes@nitrofreeze.com Shrink fitting, (or “compression fitting” as it is sometimes called), is a method used to insert a pin or bushing into a housing or other assembly requiring an extremely tight tolerance fit. It can be used as an alternative to...
Telecommunications
From the Winter 2004 issue of Cold Facts magazine The recent M-Calc IV — 4th Industry Assessment workshop discussing military and commercial applications for low-cost cryocoolers, held in November in San Diego, highlighted progress being made in cryogenics as applied in telecommunications. The reliability and long lifetime of projects now...
Wind Tunnels
Dr. Robert Kilgore The development of the cryogenic wind tunnel is one of many significant breakthroughs in both cryogenics and wind-tunnel technology made during the past millennium. Interest in the development of high-speed commercial and military aircraft resulted in a review of problems of flow simulation in transonic wind tunnels...
An Issue of Pressure and Flow Rate in a Supply Tank
Please help solve this problem: A supply tank requires a vaporizer to generate sufficient pressure to pump stored fluid up into a vehicle or tank. The available head is limited as the tank level falls and it is important to minimize the system pressure drop to maintain the desired flow...
Using MLI on VJ Line Joints or Cryo Storage Tanks
When installing Multi Layer Insulation (MLI) blankets on VJ line joints or cryo storage tanks should they be wrapped and tied down tight or loose? These are usually pre-cut to size. Also should they have an access hole at the point of where the molecular sieve is installed to help...
Separated layers of ice over a pipe
I want to know that why there are different layers of ice over a pipe carrying a cryogenic fluid, each layer separated with clear marks / lines? What do these layers signify?